2007-2013 Highlander Kluger · Service Manual STEERING

DISASSEMBLY

Removal / installation · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010

NOTICE:
When using a vise, do not overtighten it.


1. REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Smart Entry and Start System)
  1. Secure the steering column assembly in a vise.

  1. Using a center punch, mark the center of the 2 tapered-head bolts.

  1. Using a 3 to 4 mm (0.12 to 0.16 in.) drill, drill a hole in each tapered-head bolt.

  1. C166127E01
    Using a screw extractor, remove the 2 tapered-head bolts, and then remove the steering lock actuator assembly and the steering lock bracket from the steering column assembly.


2. REMOVE KEY CYLINDER LIGHT ASSEMBLY (w/o Engine Immobiliser System)

  1. C172130
    Using a screwdriver, widen the claws hanging onto the upper bracket by approximately 1.0 mm (0.039 in.).

  1. Pull out the key cylinder light assembly with the claw open.

    NOTICE:
    Using excessive force may damage the case.


3. REMOVE TRANSPONDER KEY AMPLIFIER (w/ Engine Immobiliser System)

  1. C115569
    Using a screwdriver, widen the claws hanging onto the upper bracket by approximately 1.0 mm (0.039 in.).

  1. Pull out the transponder key amplifier with the claw open.

    NOTICE:
    Using excessive force may damage the case.


4. REMOVE STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY (w/o Smart Entry and Start System)
  1. Secure the steering column assembly in a vise.

  1. Using a center punch, mark the center of the 2 tapered-head bolts.

  1. Using a 3 to 4 mm (0.12 to 0.16 in.) diameter drill bit, drill a hole in each tapered-head bolt.

  1. C166126E01
    Using a screw extractor, remove the 2 tapered-head bolts, and then remove the steering column upper with switch bracket assembly and the steering lock bracket from the steering column assembly.


5. REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Smart Entry and Start System)
  1. Turn the ignition switch lock cylinder assembly to the ACC position.

  1. C105482E03
    Insert a screwdriver into the hole of the steering column upper with switch bracket assembly as shown in the illustration. Pull the ignition switch lock cylinder assembly until its claw contacts the stopper of the steering column upper with switch bracket assembly.

    NOTICE:
    Make sure to pull the ignition switch lock cylinder assembly until its claw contacts the stopper of the steering column upper with switch bracket assembly. Failure to do so will affect later work operations.

  1. C105483E03
    Insert a screwdriver into the hole of the steering column upper with switch bracket assembly. Push the screwdriver downward as shown in the illustration to disengage the claw of the ignition switch lock cylinder assembly, and pull out the ignition switch lock cylinder assembly.


6. REMOVE UN-LOCK WARNING SWITCH ASSEMBLY (w/o Smart Entry and Start System)

  1. C166124E01
    Remove the un-lock warning switch assembly by pushing up the center part and releasing the 2 claws.


7. REMOVE KEY INTERLOCK SOLENOID (w/o Smart Entry and Start System)

  1. C166125
    Remove the 2 screws and the key interlock solenoid from the steering lock sub-assembly.


8. REMOVE IGNITION OR STARTER SWITCH ASSEMBLY (w/o Smart Entry and Start System)

  1. C104552E03
    Disengage the 2 claws and remove the ignition or starter switch assembly from the steering lock sub-assembly.

← REMOVAL (from Jul 2010)DISASSEMBLY (from Jul 2010) →