2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1800/51 Short in Driver Side Squib Circuit

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

  1. The driver side squib circuit consists of the center airbag sensor assembly, the spiral cable and the steering pad.
  2. The circuit instructs the SRS to deploy when deployment conditions are met.
  3. These DTCs are recorded when a malfunction is detected in the driver side squib circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1800/51
  1. The center airbag sensor assembly receives a line short circuit signal 5 times in the driver side squib circuit during primary check.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1801/51
  1. The center airbag sensor assembly receives an open circuit signal in the driver side squib circuit for 2 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1802/51
  1. The center airbag sensor assembly receives a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly
B1803/51
  1. The center airbag sensor assembly receives a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.
  2. Driver side squib malfunction
  3. Spiral cable malfunction
  4. Center airbag sensor assembly malfunction
  1. Instrument panel wire
  2. Spiral cable
  3. Steering pad (Driver side squib)
  4. Center airbag sensor assembly

WIRING DIAGRAM

C145466E07

INSPECTION PROCEDURE

HINT:
  1. Perform the simulation method by selecting the "check mode" (signal check) with the intelligent tester (Click here).
  2. After selecting the "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).


1. CHECK CONNECTORS

  1. C165138E01
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the steering pad, spiral cable and center airbag sensor assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the steering pad, spiral cable and center airbag sensor assembly.

  1. Check that the connector terminals are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the spiral cable connector (on the steering pad side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2. CHECK STEERING PAD (DRIVER SIDE SQUIB)

  1. C145468E05
    Connect the instrument panel wire to the center airbag sensor assembly and spiral cable.

  1. Connect SST (resistance 2.1 Ω) to connector E (Orange connector).

    CAUTION:
    Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1800, B1801, B1802, B1803, or 51 is not output.

    HINT:
    Codes other than DTC B1800, B1801, B1802, B1803, and 51 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

REPLACE STEERING PAD (Click here)

3. CHECK DRIVER SIDE SQUIB CIRCUIT

  1. C157576E06
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.

  1. Disconnect the instrument panel wire from the center airbag sensor assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      z3-1 (D-) - Body ground
      Ignition switch on (IG)
      Below 1 V
      z3-2 (D+) - Body ground
      Ignition switch on (IG)
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z3-1 (D-) - z3-2 (D+)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z3-1 (D-) - Body ground
      Always
      1 MΩ or higher
      z3-2 (D+) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z3-1 (D-) - z3-2 (D+)
      Always
      1 MΩ or higher



NG
Go to step 4
OK


4. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C114806E01
    Restore the released activation prevention mechanism of connector B to the original condition.

  1. Connect the connectors to the steering pad and the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1800, B1801, B1802, B1803, or 51 is not output.

    HINT:
    Codes other than DTC B1800, B1801, B1802, B1803, and 51 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)

5. CHECK INSTRUMENT PANEL WIRE

  1. C167900E03
    Restore the released activation prevention mechanism of connector B to the original condition.

  1. Disconnect the instrument panel wire from the spiral cable.

  1. Check for a short to B+ in the circuit.

    1. Connect the negative (-) terminal cable to the battery.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      D52-1 (D+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      D52-2 (D-) - Body ground
      Ignition switch on (IG)
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D52-1 (D+) - D52-2 (D-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D52-1 (D+) - Body ground
      Always
      1 MΩ or higher
      D52-2 (D-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      D52-1 (D+) - D52-2 (D-)
      Always
      1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK


6. CHECK SPIRAL CABLE

  1. C157585E06
    Check for a short to B+ in the circuit.
    1. Connect the negative (-) terminal cable to the battery.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      z3-1 (D-) - Body ground
      Ignition switch on (IG)
      Below 1 V
      z3-2 (D+) - Body ground
      Ignition switch on (IG)
      Below 1 V

  1. Check for an open in the circuit.

    1. Turn the ignition switch off.

    2. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z3-1 (D-) - z3-2 (D+)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z3-1 (D-) - Body ground
      Always
      1 MΩ or higher
      z3-2 (D+) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector D (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      z3-1 (D-) - z3-2 (D+)
      Always
      1 MΩ or higher



NG
REPLACE SPIRAL CABLE (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1800/51 Short in Driver Side Squib Circuit (+ B1801/51, B1802/51, B1803/51) (May 2007 – Jul 2008)B1800/51 Short in Driver Side Squib Circuit (+ B1801/51, B1802/51, B1803/51) (from Jul 2010) →