2007-2013 Highlander Kluger · Service Manual ENGINE

P0351 Ignition Coil "A" Primary / Secondary Circuit

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. High-voltage is generated in the secondary wiring and then applied directly to each spark plug. The sparks of the spark plugs pass from the center electrodes to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, high- voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil off, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.
A133853E06
DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal to ECM while engine is running (1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT (1 to 6) circuit between ignition coil with igniter and ECM
  3. No. 1 to No. 6 ignition coils with igniters
  4. ECM
Reference: Inspection using an oscilloscope
A140712E01
While cranking or idling, check the waveform between terminals IGT (1 to 6) and E1, and IGF1 and E1 of the ECM connector.
Item
Content
Terminals
CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
CH2: IGF1 - E1
Equipment Settings
2 V/DIV., 20 ms./DIV.
Conditions
Cranking or idling

WIRING DIAGRAM

A140713E04
A172771E02
A172772E02

INSPECTION PROCEDURE

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is set, check the No. 1 ignition coil circuit.
  3. If DTC P0352 is set, check the No. 2 ignition coil circuit.
  4. If DTC P0353 is set, check the No. 3 ignition coil circuit.
  5. If DTC P0354 is set, check the No. 4 ignition coil circuit.
  6. If DTC P0355 is set, check the No. 5 ignition coil circuit.
  7. If DTC P0356 is set, check the No. 6 ignition coil circuit.
  8. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK DTC OUTPUT
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menu items: Powertrain / Engine and ECT / DTC.

  1. Read the DTC.

    Result:
    Result
    Proceed to
    DTC P0351, P0352, P0353, P0354 or P0356 is output
    A
    P0351, P0352, P0353, P0354 and P0356 are output
    B



B
Go to step 6
A


2. CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Shuffle arrangement of the ignition coils with igniters (among No. 1 to No. 6 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Perform a simulation test.

  1. Check the DTCs displayed on the tester.

    Result:
    Result
    Proceed to
    Same DTC output
    A
    Different ignition coil DTC output
    B



B
REPLACE IGNITION COIL ASSEMBLY (MALFUNCTIONING CYLINDER) (Click here)
A


3. CHECK IGNITION COIL ASSEMBLY (POWER SOURCE)

  1. A157860E16
    Disconnect the ignition coil connector of malfunctioning cylinder.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (+B) - Body ground
    Ignition switch on (IG)
    9 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the ignition coil connector.



NG
Go to step 6
OK


4. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

  1. A168211E04
    Disconnect the ignition coil connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B30-2 (IGF) - B1-24 (IGF1)
    Always
    Below 1 Ω
    B31-2 (IGF) - B1-24 (IGF1)
    Always
    Below 1 Ω
    B32-2 (IGF) - B1-24 (IGF1)
    Always
    Below 1 Ω
    B33-2 (IGF) - B1-24 (IGF1)
    Always
    Below 1 Ω
    B34-2 (IGF) - B1-24 (IGF1)
    Always
    Below 1 Ω
    B35-2 (IGF) - B1-24 (IGF1)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B30-2 (IGF) or B1-24 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B31-2 (IGF) or B1-24 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B32-2 (IGF) or B1-24 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B33-2 (IGF) or B1-24 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B34-2 (IGF) or B1-24 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B35-2 (IGF) or B1-24 (IGF1) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ignition coil connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
OK


5. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

  1. A168211E05
    Disconnect the ignition coil connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B30-3 (IGT1) - B1-8 (IGT1)
    Always
    Below 1 Ω
    B31-3 (IGT2) - B1-9 (IGT2)
    Always
    Below 1 Ω
    B32-3 (IGT3) - B1-10 (IGT3)
    Always
    Below 1 Ω
    B33-3 (IGT4) - B1-11 (IGT4)
    Always
    Below 1 Ω
    B34-3 (IGT5) - B1-12 (IGT5)
    Always
    Below 1 Ω
    B35-3 (IGT6) - B1-13 (IGT6)
    Always
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B30-3 (IGT1) or B1-8 (IGT1) - Body ground
    Always
    10 kΩ or higher
    B31-3 (IGT2) or B1-9 (IGT2) - Body ground
    Always
    10 kΩ or higher
    B32-3 (IGT3) or B1-10 (IGT3) - Body ground
    Always
    10 kΩ or higher
    B33-3 (IGT4) or B1-11 (IGT4) - Body ground
    Always
    10 kΩ or higher
    B34-3 (IGT5) or B1-12 (IGT5) - Body ground
    Always
    10 kΩ or higher
    B35-3 (IGT6) or B1-13 (IGT6) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ignition coil connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)

6. INSPECT FUSE (INJ NO. 1 FUSE)

  1. A168235E03
    Remove the INJ No. 1 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    INJ No. 1 fuse
    Always
    Below 1 Ω

  1. Reinstall the fuse.



NG
REPLACE FUSE (INJ NO. 1 FUSE)
OK


7. INSPECT RELAY (IG2 RELAY)

  1. B016200
    Remove the IG2 relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    No battery
    10 kΩ or higher
    3 - 5
    When battery voltage applied to terminals 1 and 2
    Below 1 Ω

  1. Reinstall the IG2 relay.



NG
REPLACE RELAY
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - INJ NO. 1 FUSE)


← P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 5 more codes) (May 2007 – Jul 2008)P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 5 more codes) (from Jul 2010) →