2007-2013 Highlander Kluger · Service Manual ENGINE

P0351 Ignition Coil "A" Primary / Secondary Circuit

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

CAUTION / NOTICE / HINT

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is set, check the No. 1 ignition coil assembly circuit.
  3. If DTC P0352 is set, check the No. 2 ignition coil assembly circuit.
  4. If DTC P0353 is set, check the No. 3 ignition coil assembly circuit.
  5. If DTC P0354 is set, check the No. 4 ignition coil assembly circuit.
  6. If DTC P0355 is set, check the No. 5 ignition coil assembly circuit.
  7. If DTC P0356 is set, check the No. 6 ignition coil assembly circuit.


DESCRIPTION

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. High-voltage is generated in the secondary wiring and then applied directly to each spark plug. The sparks of the spark plugs pass from the center electrodes to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, high- voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil off, the igniter sends back an ignition confirmation (IGF) signal to the ECM, for each cylinder ignition.
A240478E02
DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal to ECM while engine is running (1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 6) between ignition coil assembly and ECM
  3. No. 1 to No. 6 ignition coils assemblies
  4. ECM
Reference: Inspection using an oscilloscope
A140712E01
While cranking or idling, check the waveform between terminals IGT (1 to 6) and E1, and IGF1 and E1 of the ECM connector.
Item
Content
Terminals
CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
CH2: IGF1 - E1
Equipment Settings
2 V/DIV., 20 ms./DIV.
Conditions
Idling

WIRING DIAGRAM

A140713E17
A172771E07
A172772E06

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353, P0354, P0355 OR P0356)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the tester on.

  1. Clear the DTCs (Click here).

  1. Shuffle arrangement of the ignition coil assemblies (among No. 1 to No. 6 cylinders).

    NOTICE:
    Do not shuffle the connectors.

  1. Perform a simulation test.

  1. Check the DTCs displayed on the tester.

    Result:
    Result
    Proceed to
    Same DTC output
    A
    Different ignition coil DTC output
    B



B
REPLACE IGNITION COIL ASSEMBLY (MALFUNCTIONING CYLINDER) (Click here)
A


2. CHECK IGNITION COIL ASSEMBLY (POWER SOURCE)

  1. A157860E50
    Disconnect the ignition coil assembly connector of malfunctioning cylinder.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B30-1 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    B31-1 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    B32-1 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    B33-1 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    B34-1 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    B35-1 (+B) - Body ground
    Ignition switch on (IG)
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Ignition Coil Assembly)

  1. Reconnect the ignition coil assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG2 RELAY - IGNITION COIL)
OK


3. CHECK HARNESS AND CONNECTOR (IGNITION COIL - BODY GROUND)
  1. Disconnect the ignition coil connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    B30-4 (GND) - Body ground
    Always
    Below 1 Ω
    B31-4 (GND) - Body ground
    Always
    Below 1 Ω
    B32-4 (GND) - Body ground
    Always
    Below 1 Ω
    B33-4 (GND) - Body ground
    Always
    Below 1 Ω
    B34-4 (GND) - Body ground
    Always
    Below 1 Ω
    B35-4 (GND) - Body ground
    Always
    Below 1 Ω

  1. Reconnect the ignition connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the ignition coil assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B30-2 (IGF) - B48-6 (IGF1)
    Always
    Below 1 Ω
    B31-2 (IGF) - B48-6 (IGF1)
    Always
    Below 1 Ω
    B32-2 (IGF) - B48-6 (IGF1)
    Always
    Below 1 Ω
    B33-2 (IGF) - B48-6 (IGF1)
    Always
    Below 1 Ω
    B34-2 (IGF) - B48-6 (IGF1)
    Always
    Below 1 Ω
    B35-2 (IGF) - B48-6 (IGF1)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B30-2 (IGF) or B48-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B31-2 (IGF) or B48-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B32-2 (IGF) or B48-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B33-2 (IGF) or B48-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B34-2 (IGF) or B48-6 (IGF1) - Body ground
    Always
    10 kΩ or higher
    B35-2 (IGF) or B48-6 (IGF1) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the ignition coil assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
OK


5. CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the ignition coil assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    B30-3 (IGT1) - B48-24 (IGT1)
    Always
    Below 1 Ω
    B31-3 (IGT2) - B48-25 (IGT2)
    Always
    Below 1 Ω
    B32-3 (IGT3) - B48-26 (IGT3)
    Always
    Below 1 Ω
    B33-3 (IGT4) - B48-27 (IGT4)
    Always
    Below 1 Ω
    B34-3 (IGT5) - B48-28 (IGT5)
    Always
    Below 1 Ω
    B35-3 (IGT6) - B49-25 (IGT6)
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    B30-3 (IGT1) or B48-24 (IGT1) - Body ground
    Always
    10 kΩ or higher
    B31-3 (IGT2) or B48-25 (IGT2) - Body ground
    Always
    10 kΩ or higher
    B32-3 (IGT3) or B48-26 (IGT3) - Body ground
    Always
    10 kΩ or higher
    B33-3 (IGT4) or B48-27 (IGT4) - Body ground
    Always
    10 kΩ or higher
    B34-3 (IGT5) or B48-28 (IGT5) - Body ground
    Always
    10 kΩ or higher
    B35-3 (IGT6) or B49-25 (IGT6) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ignition coil assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)


← P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 5 more codes) (Aug 2008 – Jun 2010)P0365 Camshaft Position Sensor "B" Circuit (Bank 1) (+ 5 more codes) (May 2007 – Jun 2010) →