2007-2013 Highlander Kluger · Service Manual ENGINE

P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1)

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The Variable Valve Timing (VVT) system includes the ECM, camshaft timing oil control valve assembly and VVT controller. The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the camshaft timing oil control valve assembly, based on the signals transmitted by several sensors. The VVT controller regulates the exhaust camshaft angle using oil pressure through the camshaft timing oil control valve assembly. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual exhaust valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target exhaust valve timing is verified by the ECM.
A236702E03
DTC No.
DTC Detection Condition
Trouble Area
P0013
Open or short in camshaft timing oil control valve assembly for exhaust camshaft (bank 1) circuit
(1 trip detection logic)
  1. Open or short in camshaft timing oil control valve assembly for exhaust camshaft (bank 1) circuit
  2. Camshaft timing oil control valve assembly for exhaust camshaft (bank 1)
  3. ECM
P0023
Open or short in camshaft timing oil control valve assembly for exhaust camshaft (bank 2) circuit
(1 trip detection logic)
  1. Open or short in camshaft timing oil control valve assembly for exhaust camshaft (bank 2) circuit
  2. Camshaft timing oil control valve assembly for exhaust camshaft (bank 2)
  3. ECM

WIRING DIAGRAM

A133849E27

INSPECTION PROCEDURE

HINT:
  1. If DTC P0013 is displayed, check the exhaust camshaft circuit for the bank 1 VVT system.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  4. If DTC P0023 is displayed, check the exhaust camshaft circuit for the bank 2 VVT system.
  5. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OIL CONTROL VALVE FOR EXHAUST CAMSHAFT)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain/ Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).

  1. Check the engine speed while operating the camshaft timing oil control valve assembly using the tester.

    OK:
    Tester Operation
    Specified Condition
    0%
    Normal engine speed
    100%
    Engine idles roughly or stalls



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A233347E01
    Remove the camshaft timing oil control valve assembly (for exhaust camshaft).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    6.9 to 7.9 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft))

  1. A236713E01
    Connect the positive (+) battery terminal to terminal 1 and connect the negative (-) battery terminal to terminal 2. Check the valve operation.

    OK:
    Valve moves quickly.

  1. Reinstall the camshaft timing oil control valve assembly (for exhaust camshaft).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
  1. Disconnect the exhaust camshaft timing oil control valve assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B49-21 (OE1+) - B43-1
    Always
    Below 1 Ω
    B49-22 (OE1-) - B43-2
    Always
    Below 1 Ω
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B50-21 (OE2+) - B40-1
    Always
    Below 1 Ω
    B50-22 (OE2-) - B40-2
    Always
    Below 1 Ω


    Standard resistance (Check for short):
    Bank 1:
    Tester Connection
    Condition
    Specified Condition
    B49-21 (OE1+) or B43-1 - Body ground
    Always
    10 kΩ or higher
    B49-22 (OE1-) or B43-2 - Body ground
    Always
    10 kΩ or higher
    Bank 2:
    Tester Connection
    Condition
    Specified Condition
    B50-21 (OE2+) or B40-1 - Body ground
    Always
    10 kΩ or higher
    B50-22 (OE2-) or B40-2 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the camshaft timing oil control valve assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)


← P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1) (+ P0023) (Aug 2008 – Jun 2010)P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1) (+ P0015, P0024, P0025) (May 2007 – Jul 2008) →