P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1)
Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008
Also covers:
- P0023 Camshaft Position "B" Actuator Circuit / Open (Bank 2)
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
- HINT:
- These DTCs relate to the oil control valve for the exhaust camshaft.
The ECM controls the oil control valve, based on the signals output from the sensors. The variable valve timing controller regulates the exhaust camshaft angle using oil pressure through the oil control valve. As a result, the relative position between the camshaft and the crankshaft becomes optimal, and the engine torque and fuel economy improve, and exhaust emissions decrease under overall driving conditions. Also, the ECM detects the actual valve timing using the signals from the camshaft position sensor and the crankshaft position sensor, and performs feedback control. This is how target valve timing is achieved by the ECM.


| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0013 |
Open or short in oil control valve exhaust camshaft circuit (1 trip detection logic) |
|
| P0023 |
Open or short in oil control valve exhaust camshaft circuit (1 trip detection logic) |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If DTC P0013 is displayed, check the exhaust camshaft circuit for the right bank variable valve timing system.
- If DTC P0023 is displayed, check the exhaust camshaft circuit for the left bank variable valve timing system.
- Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.
- If DTC P0013 is displayed, check the exhaust camshaft circuit for the right bank variable valve timing system.
| 1. CHECK WHETHER DTC OUTPUT RECURS (DTC P0013 OR P0023) |
Connect an intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / DTC / Clear.
Clear the DTCs.
Start the engine and warm it up.
Allow the engine to idle 1 minute or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
- Result:
Result
Proceed to
P0013 or P0023
A
No output
B
|
|
||||
| A | |
| 2. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) |
Disconnect the exhaust camshaft timing oil control valve connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω
Reconnect the oil control valve connector.
|
|
||||
| OK | |
| 3. CHECK ECM (OIL CONTROL VALVE SIGNAL) |
Disconnect the camshaft timing oil control valve connector.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance (Check for open):
- Bank 1:
Tester Connection
Condition
Specified Condition
B3-26 (OE1+) - B43-1
Always
Below 1 Ω
B3-31 (OE1-) - B43-2
Always
Below 1 Ω
- Bank 2:
Tester Connection
Condition
Specified Condition
B3-27 (OE2+) - B40-1
Always
Below 1 Ω
B3-32 (OE2-) - B40-2
Always
Below 1 Ω
- Standard resistance (Check for short):
- Bank 1:
Tester Connection
Condition
Specified Condition
B3-26 (OE1+) or B43-1 - Body ground
Always
10 kΩ or higher
B3-31 (OE1-) or B43-2 - Body ground
Always
10 kΩ or higher
- Bank 2:
Tester Connection
Condition
Specified Condition
B3-27 (OE2+) or B40-1 - Body ground
Always
10 kΩ or higher
B3-32 (OE2-) or B40-2 - Body ground
Always
10 kΩ or higher
Reconnect the ECM connector.
Reconnect the oil control valve connector.
|
|
||||
| OK | ||
| ||
