2007-2013 Highlander Kluger · Service Manual BRAKE

FREEZE FRAME DATA

Troubleshooting · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


FREEZE FRAME DATA
  1. Whenever an ABS DTC is detected, the skid control ECU stores the current vehicle (sensor) state as Freeze Frame Data.

  2. The skid control ECU stores the number of times (maximum: 31) the ignition switch has been turned from off to on (IG) since the last time the ABS was activated.

    HINT:
    1. If the vehicle is stopped or at a low speed (7 km/h (4.3 mph) or less), or if a DTC is detected, the skid control ECU will stop counting the number.
    2. Freeze Frame Data at the time the ABS operates:
      The skid control ECU stores and updates data whenever the ABS system operates.
      When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is erased.
    3. Freeze Frame Data at the time a DTC is detected:
      When the skid control ECU stores data at the time a DTC is detected, no updates will be performed until the data is cleared.


CHECK FREEZE FRAME DATA
  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Chassis / ABS/VSC/TRC / DTC.

  5. According to the display on the tester, select the DTC data display with Freeze Frame Data.

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item
    Reference Value
    Elapsed Time after Freeze Trigger
    Elapsed time after freeze frame trigger
    Min.: 0 ms, Max.: 500 ms
    Number of IG ON
    Number of operations of ignition switch being turned on (IG) after storing Freeze Frame Data
    0 to 31
    Buzzer
    Skid control buzzer signal
    Skid control buzzer ON: ON, OFF: OFF
    Stop Lamp SW
    Stop light switch signal
    Stop light switch ON: ON, OFF: OFF
    Parking Brake SW
    Parking brake switch signal
    Parking brake switch ON: ON, OFF: OFF
    TRC (TRAC)/VSC OFF SW
    VSC OFF switch signal
    VSC OFF switch ON: OFF, OFF: ON
    Gear Position
    Gear position information
    FAIL
    1st
    2nd
    3rd
    4th
    5th
    6th
    7th
    8th
    P, N
    R
    NOT R
    Shift Lever Position
    Shift lever position information
    FAIL
    1st
    2nd
    3rd
    4th
    5th
    6th/B
    D/M
    P, N
    R
    Operated System
    Operated system status
    ABS: ABS activated
    VSC: VSC activated
    TRC: TRC activated
    BA: BA activated
    HAB: HAB activated
    HA-CTRL: Hill-start assist control activated
    FAIL: Fail safe mode activated
    SYS: System prohibit activated
    NON: No operation activated
    Master Cylinder Sensor
    Master cylinder pressure sensor reading
    Brake pedal released: 0.3 to 0.9 V
    Brake pedal depressed: 0.8 to 4.5 V
    M/C Sensor Grade
    Master cylinder pressure sensor change
    Min.: -30 MPa/s, Max.: 225 MPa/s
    Yaw Rate Sensor
    Yaw rate sensor reading
    Min.: -128 deg/s, Max.: 127 deg/s
    Lateral G
    Lateral G
    Min.: -25.11 m/s2, Max.: 24.91 m/s2
    Forward and Rearward G
    Forward and backward G
    Min.: -25.11 m/s2, Max.: 24.91 m/s2
    FR Wheel Speed
    FR wheel speed
    Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    FL Wheel Speed
    FL wheel speed
    Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    RR Wheel Speed
    RR wheel speed
    Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    RL Wheel Speed
    RL wheel speed
    Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle Speed
    Vehicle speed reading
    Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle Speed Grade
    Vehicle speed grade
    Min.: -25.11 m/s2, Max.: 24.91 m/s2
    Real Engine Torque
    Real engine torque
    Min.: -1024 Nm, Max.: 1023 Nm
    Accelerator Opening Angle %
    Accelerator opening Angle %
    Min.: 0 %, Max.: 128 %
    Brake Pedal Load Sensing SW
    Brake pedal load sensing switch signal
    Brake pedal load sensing switch ON: ON, OFF: OFF
    Steering Angle Sensor
    Steering angle sensor reading
    Left turn: Increase
    Right turn: Decrease


CLEAR FREEZE FRAME DATA

NOTICE:
Clearing the DTCs will also clear the Freeze Frame Data.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch on (IG).

  3. Clear the DTCs and Freeze Frame Data (Click here).

← DTC CHECK / CLEAR (from Jul 2010)FREEZE FRAME DATA (Aug 2008 – Jun 2010) →