C1401 Front Speed Sensor RH Malfunction
Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008
Also covers:
- C1402 Front Speed Sensor LH Malfunction
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The speed sensor detects wheel speed and sends the appropriate signals to the skid control ECU. These signals are used for ABS control.Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn.
Each speed sensor detects that magnetic change and sends a pulse signal to the skid control ECU.


| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1401 C1402 |
Any of the following is detected:
|
|
- HINT:
- DTC C1401 is for the front speed sensor RH.
- DTC C1402 is for the front speed sensor LH.
- DTC C1401 is for the front speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK FRONT SPEED SENSOR INSTALLATION |
Check the speed sensor installation.

- OK:
- There is no clearance between the sensor and the front steering knuckle.
- The installation nut is tightened properly.
- Torque:
- 8.0 N*m (82 kgf*cm, 71 in.*lbf)
|
|
||||
| OK | |
| 2. CHECK FRONT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the speed sensor tip.
- OK:
- No scratches, oil, or foreign matter on the sensor tip.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
|
|
||||
| OK | |
| 3. CHECK FRONT SPEED SENSOR ROTOR |
Remove the front speed sensor rotor (Click here).
Check the speed sensor rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
- HINT:
- If the front speed sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
|
|
||||
| OK | |
| 4. READ VALUE ON INTELLIGENT TESTER (FRONT SPEED SENSOR) |
Install the front speed sensor and the front speed sensor rotor.
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List mode on the intelligent tester (Click here).
ABS / VSC / TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Wheel Speed
FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
FL Wheel Speed
FL wheel speed sensor reading /min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
- HINT:
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
|
|
||||
| OK | ||
| ||
| 5. REPLACE FRONT SPEED SENSOR |
Turn the ignition switch off.
Replace the front speed sensor (Click here).
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
| NEXT | |
| 6. RECONFIRM DTC |
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
- Result:
Result
Proceed to
DTCs (C1401 and C1402) are not output
A
DTCs (C1401 and/or C1402) are output
B
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
- HINT:
- If the front speed sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
- If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).
- If the front speed sensor rotor needs to be replaced, replace it together with the front drive shaft assembly.
|
|
||||
| A | ||
| ||
