2007-2013 Highlander Kluger · Service Manual BRAKE

ABS Warning Light Remains ON

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
If any of the following is detected, the ABS warning light remains on:
  1. The skid control ECU connectors are disconnected from the skid control ECU.
  2. There is a malfunction in the skid control ECU internal circuit.
  3. There is an open in the harness between the combination meter and the skid control ECU.
  4. The ABS control system is defective.

HINT:
  1. For vehicles with the multi-information display, the master caution indicator light will come on and a check ABS message will be displayed on the multi-information display if the ABS control cannot be performed.
  2. In some cases, the intelligent tester cannot be used when the skid control ECU is abnormal.


WIRING DIAGRAM

C167286E02

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3. CHECK BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (for 2GR-FE) (Click here)
OK


4. INSPECT SKID CONTROL ECU (IG1 TERMINAL)

  1. C160263E43
    Disconnect the skid control ECU connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A24-34 (IG1) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5. INSPECT SKID CONTROL ECU (GND1 TERMINAL)

  1. C160263E41
    Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


6. INSPECT COMBINATION METER ASSEMBLY
  1. Reconnect the skid control ECU connector.

  1. Perform the Active Test of the combination meter (meter CPU) using the intelligent tester (Click here).

  1. Check the combination meter.

    OK:
    The ABS warning light turns on or off in accordance with the intelligent tester operation.

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← ABS Warning Light Remains ON (May 2007 – Jul 2008)ABS Warning Light Remains ON (Jul 2010 – Jun 2012) →