2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Driver Side Door Entry Lock and Unlock Functions do not Operate

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

When the driver door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) power door lock system, 2) driver side door electrical key oscillator, or 3) certification ECU (smart key ECU assembly).

WIRING DIAGRAM

B164403E08

INSPECTION PROCEDURE

NOTICE:
Before performing the inspection, check that there are no problems related to "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".


1. CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the master switch assembly is operated, check that the locked doors unlock (Click here).

    OK:
    Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. READ VALUE ON INTELLIGENT TESTER (DOOR OUTSIDE HANDLE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Select D Touch Sensor or D Trigger SW in the Data List and read the tester display.

    Entry & Start (Certification ECU (Smart Key ECU Assembly)): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Touch Sensor
    Driver side door touch sensor / ON or OFF
    ON: Touch sensor is touched
    OFF: Touch sensor is not touched
    -
    D Trigger SW
    Driver side door lock switch / ON or OFF
    ON: Entry lock switch is pressed
    OFF: Entry lock switch is not pressed
    -

    OK:
    On the tester screen, each item changes between ON and OFF according to the chart above.



NG
REPLACE FRONT DOOR OUTSIDE HANDLE (Click here)
OK


3. CHECK WAVE ENVIRONMENT

  1. B180399E01
    Bring the electrical key transmitter near the driver door outside handle, and perform a driver door entry lock and unlock operation check.

    NOTICE:
    If the key is brought within 0.2 m (0.656 ft.) of the door outside handle, communication is not possible.

    HINT:
    1. When the electrical key transmitter is brought near the driver door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    OK:
    Entry functions operate normally.



NG
Go to step 4
OK

AFFECTED BY WAVE INTERFERENCE

4. PERFORM KEY DIAGNOSTIC MODE INSPECTION

  1. B180399E03
    Diagnostic mode inspection (driver door electrical key oscillator)
    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the tester on.

    4. Enter the following menus:Body / Entry & Start / Key Communication Check / Overhead + Driver Side.

    5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.

      HINT:
      If the buzzer sounds, it can be determined that the driver door electrical key oscillator is operating normally.

      OK:
      Wireless door lock buzzer sounds.



NG
Go to step 5
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)

  1. B171407E07
    Disconnect the certification ECU (smart key ECU assembly) and door electrical key oscillator connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    D36-5 (SEL1) - z14-4 (SEL)
    Always
    Below 1 Ω
    D36-34 (CG1B) - z14-5 (CLGB)
    Always
    Below 1 Ω
    D36-5 (SEL1) - Body ground
    Always
    10 kΩ or higher
    D36-34 (CG1B) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    D36-5 (SEL1) - z16-4 (SEL)
    Always
    Below 1 Ω
    D36-34 (CG1B) - z16-5 (CLGB)
    Always
    Below 1 Ω
    D36-5 (SEL1) - Body ground
    Always
    10 kΩ or higher
    D36-34 (CG1B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)

  1. B164339E31
    Remove the front door outside handle (Click here).

  1. Disconnect the door antenna connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    z13-2 (ANT2) - z14-8 (ANT2)
    Always
    Below 1 Ω
    z13-5 (ANT1) - z14-3 (ANT1)
    Always
    Below 1 Ω
    z13-2 (ANT2) - Body ground
    Always
    10 kΩ or higher
    z13-5 (ANT1) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    z15-2 (ANT2) - z16-8 (ANT2)
    Always
    Below 1 Ω
    z15-5 (ANT1) - z16-3 (ANT1)
    Always
    Below 1 Ω
    z15-2 (ANT2) - Body ground
    Always
    10 kΩ or higher
    z15-5 (ANT1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT FUSE (ECU-B)
  1. Remove the ECU-B fuse from the engine room junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-B fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE (ECU-B)
OK


Go to step 9

8. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)

  1. B164336E12
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    z14-1 (+B) - z14-7 (GND)
    Always
    11 to 14 V
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    z16-1 (+B) - z16-7 (GND)
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. REPLACE DOOR ELECTRICAL KEY OSCILLATOR
  1. Replace the door electrical key oscillator (Click here).


NEXT


10. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
  1. Check that the entry functions operate normally.

    OK:
    Entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)


← Front Passenger Side Door Entry Unlock Function does not Operate (from Jul 2010)Driver Side Door Entry Lock and Unlock Functions do not Operate (Aug 2008 – Jun 2010) →