2007-2013 Highlander Kluger · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and light remainder warning system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches, or the doors. If any doors need to be opened in order to check the connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN.
This communication will cause the resistance value to change.

NOTICE:
This section describes the standard CAN values for all CAN related components.


JUNCTION CONNECTOR FOR CAN BUS (for LHD)

  1. CAN junction connector CTR
    C132298E28

    CAN Junction Connector CTR
    Wiring Color
    Connect to
    D47-1 (CANH)
    SB
    CAN junction connector RH
    D47-12 (CANL)
    W
    CAN junction connector RH
    D47-2 (CANH)
    V
    Yaw rate sensor
    D47-13 (CANL)
    W
    Yaw rate sensor
    D47-3 (CANH)
    Y
    Center airbag sensor assembly
    D47-14 (CANL)
    W
    Center airbag sensor assembly
    D47-4 (CANH)
    L
    DLC3
    D47-15 (CANL)
    W
    DLC3
    D47-5 (CANH)
    R
    Steering angle sensor
    D47-16 (CANL)
    W
    Steering angle sensor
    D47-6 (CANH)
    P
    Combination meter
    D47-17 (CANL)
    W
    Combination meter
    D47-7 (CANH)
    BR
    Power steering ECU
    D47-18 (CANL)
    W
    Power steering ECU
    D47-8 (CANH)
    GR
    Main body ECU
    D47-19 (CANL)
    W
    Main body ECU
    D47-9 (CANH)
    SB
    Television camera ECU
    D47-20 (CANL)
    W
    Television camera ECU

  2. CAN junction connector RH
    C132298E29

    CAN Junction Connector RH
    Wiring Color
    Connect to
    D51-1 (CANH)
    R
    ECM
    D51-12 (CANL)
    W
    ECM
    D51-3 (CANH)
    LG
    Air conditioning amplifier
    D51-14 (CANL)
    W
    Air conditioning amplifier
    D51-4 (CANH)
    B
    Skid control ECU
    D51-15 (CANL)
    W
    Skid control ECU
    D51-5 (CANH)
    SB
    CAN junction connector CTR
    D51-16 (CANL)
    W
    CAN junction connector CTR

  3. The connection diagram of the components which are connected to the CAN junction connector.
    C170360E04


JUNCTION CONNECTOR FOR CAN BUS (for RHD)

  1. CAN junction connector CTR
    C132298E28

    CAN Junction Connector CTR
    Wiring Color
    Connect to
    D47-1 (CANH)
    SB
    CAN junction connector RH
    D47-12 (CANL)
    W
    CAN junction connector RH
    D47-2 (CANH)
    G
    Yaw rate sensor
    D47-13 (CANL)
    W
    Yaw rate sensor
    D47-3 (CANH)
    Y
    Center airbag sensor assembly
    D47-14 (CANL)
    W
    Center airbag sensor assembly
    D47-4 (CANH)
    L
    DLC3
    D47-15 (CANL)
    W
    DLC3
    D47-5 (CANH)
    R
    ECM
    D47-16 (CANL)
    W
    ECM
    D47-6 (CANH)
    P
    Air conditioning amplifier
    D47-17 (CANL)
    W
    Air conditioning amplifier
    D47-8 (CANH)
    GR
    Main body ECU
    D47-19 (CANL)
    W
    Main body ECU

  2. CAN junction connector RH
    C132298E29

    CAN Junction Connector RH
    Wiring Color
    Connect to
    D51-1 (CANH)
    R
    Steering angle sensor
    D51-12 (CANL)
    W
    Steering angle sensor
    D51-2 (CANH)
    BR
    Power steering ECU
    D51-13 (CANL)
    W
    Power steering ECU
    D51-3 (CANH)
    P
    Combination meter
    D51-14 (CANL)
    W
    Combination meter
    D51-4 (CANH)
    B
    Skid control ECU
    D51-15 (CANL)
    W
    Skid control ECU
    D51-5 (CANH)
    SB
    CAN junction connector CTR
    D51-16 (CANL)
    W
    CAN junction connector CTR

  3. The connection diagram of the components which are connected to the CAN junction connector.
    C170361E01


JUNCTION CONNECTOR FOR CAN MS BUS (w/ POWER BACK DOOR SYSTEM)

  1. CAN junction connector RR
    C167481E05

    CAN Junction Connector RR
    Wiring Color
    Connect to
    O18-1 (CANH)
    B
    Back door ECU*2
    O18-2 (CANL)
    W
    Back door ECU*2
    O20-1 (CANH)
    GR
    Certification ECU*1
    O20-2 (CANL)
    W
    Certification ECU*1
    O21-1 (CANH)
    Y
    Main body ECU*2
    O21-2 (CANL)
    W
    Main body ECU*2

    HINT:
    1. *1: w/ Smart entry and start system and power back door system.
    2. *2: w/ Power back door system.

  2. The connection diagram of the components which are connected to the CAN junction connector.
    C169644E03


DLC3

  1. C125062E13
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D43-6 (CANH) - D43-14 (CANL)
    L - W
    Ignition switch off
    54 to 69 Ω
    D43-6 (CANH) - D43-4 (CG)
    L - B
    Ignition switch off
    200 Ω or higher
    D43-14 (CANL) - D43-4 (CG)
    W - B
    Ignition switch off
    200 Ω or higher
    D43-6 (CANH) - D43-16 (BAT)
    L - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D43-14 (CANL) - D43-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


SKID CONTROL ECU WITH ACTUATOR

  1. C228953E01
    Disconnect the connector from the skid control ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    A24-25 (CANH) - A24-14 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    A24-25 (CANH) - A24-1 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    A24-14 (CANL) - A24-1 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A24-25 (CANH) - A24-24 (+BM)
    B - B
    Negative battery terminal disconnected
    6 kΩ or higher
    A24-14 (CANL) - A24-24 (+BM)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


STEERING ANGLE SENSOR

  1. C146385E03
    Disconnect the connector from the steering angle sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D13-3 (CANH) - D13-2 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    D13-3 (CANH) - D13-1 (ESS)
    R - GR
    Ignition switch off
    200 Ω or higher
    D13-2 (CANL) - D13-1 (ESS)
    W - GR
    Ignition switch off
    200 Ω or higher
    D13-3 (CANH) - D13-5 (BAT)
    R - BR
    Negative battery terminal disconnected
    6 kΩ or higher
    D13-2 (CANL) - D13-5 (BAT)
    W - BR
    Negative battery terminal disconnected
    6 kΩ or higher


YAW RATE SENSOR

  1. C152858E04
    Disconnect the connector from the yaw rate sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    O6-3 (CANH) - O6-2 (CANL)
    V - W
    Ignition switch off
    54 to 69 Ω
    O6-3 (CANH) - O6-1 (GND)
    V - W-B
    Ignition switch off
    200 Ω or higher
    O6-2 (CANL) - O6-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    O6-3 (CANH) - D43-16 (BAT)
    V - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    O6-2 (CANL) - D43-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


CENTER AIRBAG SENSOR ASSEMBLY

  1. C152878E04
    Disconnect the connector from the center airbag sensor assembly.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D27-13 (CANH) - D27-22 (CANL)
    Y - W
    Ignition switch off
    54 to 69 Ω
    D27-13 (CANH) - D27-25 (E1)
    Y - B
    Ignition switch off
    200 Ω or higher
    D27-22 (CANL) - D27-25 (E1)
    W - B
    Ignition switch off
    200 Ω or higher
    D27-13 (CANH) - D43-16 (BAT)
    Y - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D27-22 (CANL) - D43-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


ECM
G035613E34
  1. Disconnect the connector from the ECM.

  2. C170023E03
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D32-33 (CANH) - D32-34 (CANL)
    R - W
    Ignition switch off
    108 to 132 Ω
    D32-33 (CANH) - B3-1 (E1)
    R - W-B
    Ignition switch off
    200 Ω or higher
    D32-34 (CANL) - B3-1 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D32-33 (CANH) - D31-3 (BATT)
    R - R
    Negative battery terminal disconnected
    6 kΩ or higher
    D32-34 (CANL) - D31-3 (BATT)
    W - R
    Negative battery terminal disconnected
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER
C152868E05
  1. Disconnect the connector from the air conditioning amplifier.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D33-11 (CANH) - D33-12 (CANL)
    LG - W (LHD)
    P - W (RHD)
    Ignition switch off
    54 to 69 Ω
    D33-11 (CANH) - D33-14 (GND)
    LG - W-B (LHD)
    P - W-B (RHD)
    Ignition switch off
    200 Ω or higher
    D33-12 (CANL) - D33-14 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D33-11 (CANH) - D33-21 (B)
    LG - B (LHD)
    P - B (RHD)
    Negative battery terminal disconnected
    6 kΩ or higher
    D33-12 (CANL) - D33-21 (B)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


COMBINATION METER

  1. C109571E20
    Disconnect the connector from the combination meter.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    E1-25 (CANH) - E1-26 (CANL)
    P - W
    Ignition switch off
    108 to 132 Ω
    E1-25 (CANH) - E1-20 (ES)
    P - R
    Ignition switch off
    200 Ω or higher
    E1-26 (CANL) - E1-20 (ES)
    W - R
    Ignition switch off
    200 Ω or higher
    E1-25 (CANH) - E1-21 (B)
    P - SB
    Negative battery terminal disconnected
    6 kΩ or higher
    E1-26 (CANL) - E1-21 (B)
    W - SB
    Negative battery terminal disconnected
    6 kΩ or higher


MAIN BODY ECU
  1. Disconnect the connector from the main body ECU.

  2. C195603E03
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D8-5 (CANH) - D8-6 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    D8-5 (CANH) - D43-4 (CG)
    GR - B
    Ignition switch off
    200 Ω or higher
    D8-6 (CANL) - D43-4 (CG)
    W - B
    Ignition switch off
    200 Ω or higher
    D8-5 (CANH) - D43-16 (BAT)
    GR - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D8-6 (CANL) - D43-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D8-16 (CANP) - D8-15 (CANN)
    Y - W
    Ignition switch off
    108 to 132 Ω
    D8-16 (CANP) - D43-4 (CG)
    Y - B
    Ignition switch off
    200 Ω or higher
    D8-15 (CANN) - D43-4 (CG)
    W - B
    Ignition switch off
    200 Ω or higher
    D8-16 (CANP) - D43-16 (BAT)
    Y - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D8-15 (CANN) - D43-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


POWER STEERING ECU

  1. C160514E08
    Disconnect the connectors from the power steering ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D5-2 (CANH) - D5-8 (CANL)
    BR - W
    Ignition switch off
    54 to 69 Ω
    D5-2 (CANH) - D4-2 (PGND)
    BR - W
    Ignition switch off
    200 Ω or higher
    D5-8 (CANL) - D4-2 (PGND)
    W - W
    Ignition switch off
    200 Ω or higher
    D5-2 (CANH) - D4-1 (PIG)
    BR - B
    Negative battery terminal disconnected
    6 kΩ or higher
    D5-8 (CANL) - D4-1 (PIG)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


CERTIFICATION ECU (w/ Smart Entry and Start System)

  1. C152870E07
    Disconnect the connector from the certification ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    D36-27 (CANH) - D36-28 (CANL)
    GR - W
    Ignition switch off
    108 to 132 Ω
    D36-27 (CANH) - D36-17 (E)
    GR - B
    Ignition switch off
    200 Ω or higher
    D36-28 (CANL) - D36-17 (E)
    W - B
    Ignition switch off
    200 Ω or higher
    D36-27 (CANH) - D36-1 (+B)
    GR - B
    Negative battery terminal disconnected
    6 kΩ or higher
    D36-28 (CANL) - D36-1 (+B)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


TELEVISION CAMERA ECU (w/ Parking Assist Monitor System)

  1. Disconnect the television camera ECU connectors.
    C168662E02

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    N15-7 (CANH) - N15-6 (CANL)
    SB - W
    Ignition switch off
    54 to 69 Ω
    N15-7 (CANH) - N16-8 (GND1)
    SB - W-B
    Ignition switch off
    200 Ω or higher
    N15-6 (CANL) - N16-8 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    N15-7 (CANH) - N16-1 (+B)
    SB - V
    Negative battery terminal disconnected
    6 kΩ or higher
    N15-6 (CANL) - N16-1 (+B)
    W - V
    Negative battery terminal disconnected
    6 kΩ or higher


BACK DOOR ECU (w/ Power Back Door System)

  1. C169769E04
    Disconnect the back door ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Terminals
    Wiring Color
    Condition
    Specified Condition
    O14-6 (MPX1) - O14-5 (MPX2)
    B - W
    Ignition switch off
    54 to 69 Ω
    O14-6 (MPX1) - O14-11 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    O14-5 (MPX2) - O14-11 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    O14-6 (MPX1) - O14-12 (B)
    B - B
    Negative battery terminal disconnected
    6 kΩ or higher
    O14-5 (MPX2) - O14-12 (B)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher

← PROBLEM SYMPTOMS TABLE (from Jul 2012)TERMINALS OF ECU (Jul 2010 – Jun 2012) →