2007-2013 Highlander Kluger · Service Manual COMMUNICATION SYSTEM

TERMINALS OF ECU

System information · Vehicles built from Jul 2012

Versions by build date: May 2007 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

NOTICE:
  1. Turn the ignition switch off before measuring the resistances of CAN bus main wires and CAN bus branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches, or the doors. If any doors need to be opened in order to check the connectors, open the doors and leave them open.
  4. This section describes the standard values for all CAN related components.

HINT:
Operating the ignition switch, any other switches, or a door triggers related ECU and sensor communication on the CAN.
This communication will cause the resistance value to change.


JUNCTION CONNECTOR FOR CAN NO. 1 BUS (for LHD)

  1. CAN junction connector CTR
    C132298E28

    CAN Junction Connector CTR
    Wiring Color
    Connected to
    D47-1 (CANH)
    SB
    CAN junction connector RH
    D47-12 (CANL)
    W
    CAN junction connector RH
    D47-2 (CANH)
    V
    Yaw rate sensor
    D47-13 (CANL)
    W
    Yaw rate sensor
    D47-3 (CANH)
    Y
    Center airbag sensor assembly
    D47-14 (CANL)
    W
    Center airbag sensor assembly
    D47-4 (CANH)
    L
    DLC3
    D47-15 (CANL)
    W
    DLC3
    D47-5 (CANH)
    R
    Steering angle sensor
    D47-16 (CANL)
    W
    Steering angle sensor
    D47-6 (CANH)
    P
    Combination meter
    D47-17 (CANL)
    W
    Combination meter
    D47-7 (CANH)
    B
    Power steering ECU
    D47-18 (CANL)
    W
    Power steering ECU
    D47-8 (CANH)
    GR
    Main body ECU
    D47-19 (CANL)
    W
    Main body ECU

  2. CAN junction connector RH
    C132298E29

    CAN Junction Connector RH
    Wiring Color
    Connected to
    D51-1 (CANH)
    R
    ECM
    D51-12 (CANL)
    W
    ECM
    D51-3 (CANH)
    LG
    Air conditioning amplifier
    D51-14 (CANL)
    W
    Air conditioning amplifier
    D51-4 (CANH)
    B
    Skid control ECU
    D51-15 (CANL)
    W
    Skid control ECU
    D51-5 (CANH)
    SB
    CAN junction connector CTR
    D51-16 (CANL)
    W
    CAN junction connector CTR

  3. The following is a connection diagram of the components that are connected to the CAN junction connectors.
    C227427E03


JUNCTION CONNECTOR FOR CAN NO. 1 BUS (for RHD)

  1. CAN junction connector CTR
    C132298E28

    CAN Junction Connector CTR
    Wiring Color
    Connected to
    D47-1 (CANH)
    SB
    CAN junction connector RH
    D47-12 (CANL)
    W
    CAN junction connector RH
    D47-2 (CANH)
    G
    Yaw rate sensor
    D47-13 (CANL)
    W
    Yaw rate sensor
    D47-3 (CANH)
    Y
    Center airbag sensor assembly
    D47-14 (CANL)
    W
    Center airbag sensor assembly
    D47-4 (CANH)
    L
    DLC3
    D47-15 (CANL)
    W
    DLC3
    D47-5 (CANH)
    R
    ECM
    D47-16 (CANL)
    W
    ECM
    D47-6 (CANH)
    P
    Air conditioning amplifier
    D47-17 (CANL)
    W
    Air conditioning amplifier
    D47-8 (CANH)
    GR
    Main body ECU
    D47-19 (CANL)
    W
    Main body ECU

  2. CAN junction connector RH
    C132298E29

    CAN Junction Connector RH
    Wiring Color
    Connected to
    D51-1 (CANH)
    R
    Steering angle sensor
    D51-12 (CANL)
    W
    Steering angle sensor
    D51-2 (CANH)
    L
    Power steering ECU
    D51-13 (CANL)
    W
    Power steering ECU
    D51-3 (CANH)
    P
    Combination meter
    D51-14 (CANL)
    W
    Combination meter
    D51-4 (CANH)
    B
    Skid control ECU
    D51-15 (CANL)
    W
    Skid control ECU
    D51-5 (CANH)
    SB
    CAN junction connector CTR
    D51-16 (CANL)
    W
    CAN junction connector CTR

  3. The following is a connection diagram of the components that are connected to the CAN junction connectors.
    C170361E02


JUNCTION CONNECTOR FOR CAN MS BUS (w/ Power Back Door System and Smart Entry and Start System)

  1. CAN junction connector RR
    C167481E12

    CAN Junction Connector RR
    Wiring Color
    Connected to
    O18-1 (CANH)
    B
    Back door ECU
    O18-2 (CANL)
    W
    Back door ECU
    O20-1 (CANH)
    GR
    Certification ECU
    O20-2 (CANL)
    W
    Certification ECU
    O21-1 (CANH)
    Y
    Main body ECU
    O21-2 (CANL)
    W
    Main body ECU

  2. The following is a connection diagram of the components that are connected to the CAN junction connector.
    C271850E01


DLC3

  1. C125062E13
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    D43-6 (CANH) - D43-14 (CANL)
    L - W
    Ignition switch off
    54 to 69 Ω
    D43-6 (CANH) - D43-4 (CG)
    L - W-B
    Ignition switch off
    200 Ω or higher
    D43-14 (CANL) - D43-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D43-6 (CANH) - D43-16 (BAT)
    L - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D43-14 (CANL) - D43-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


SKID CONTROL ECU WITH ACTUATOR

  1. C228953E01
    Disconnect the connector from the skid control ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    A24-25 (CANH) - A24-14 (CANL)
    B - W
    Ignition switch off
    54 to 69 Ω
    A24-25 (CANH) - A24-1 (GND1)
    B - W-B
    Ignition switch off
    200 Ω or higher
    A24-14 (CANL) - A24-1 (GND1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    A24-25 (CANH) - A24-24 (+BM)
    B - B
    Negative battery terminal disconnected
    6 kΩ or higher
    A24-14 (CANL) - A24-24 (+BM)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


STEERING ANGLE SENSOR

  1. C146385E03
    Disconnect the connector from the steering angle sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    D13-3 (CANH) - D13-2 (CANL)
    R - W
    Ignition switch off
    54 to 69 Ω
    D13-3 (CANH) - D13-1 (ESS)
    R - W-B
    Ignition switch off
    200 Ω or higher
    D13-2 (CANL) - D13-1 (ESS)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D13-3 (CANH) - D13-5 (BAT)
    R - V
    Negative battery terminal disconnected
    6 kΩ or higher
    D13-2 (CANL) - D13-5 (BAT)
    W - V
    Negative battery terminal disconnected
    6 kΩ or higher


YAW RATE SENSOR

  1. C152858E04
    Disconnect the connector from the yaw rate sensor.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    O6-3 (CANH) - O6-2 (CANL)
    V - W
    Ignition switch off
    54 to 69 Ω
    O6-3 (CANH) - O6-1 (GND)
    V - W-B
    Ignition switch off
    200 Ω or higher
    O6-2 (CANL) - O6-1 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    O6-3 (CANH) - D43-16 (BAT)
    V - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    O6-2 (CANL) - D43-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


CENTER AIRBAG SENSOR ASSEMBLY

  1. C152878E04
    Disconnect the connector from the center airbag sensor assembly.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    D27-13 (CANH) - D27-22 (CANL)
    Y - W
    Ignition switch off
    54 to 69 Ω
    D27-13 (CANH) - D27-25 (E1)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    D27-22 (CANL) - D27-25 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D27-13 (CANH) - D43-16 (BAT)
    Y - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D27-22 (CANL) - D43-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


ECM
A206553E11
  1. Disconnect the connectors from the ECM.

  2. C227349E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    D55-32 (CANH) - D55-31 (CANL)
    R - W
    Ignition switch off
    108 to 132 Ω
    D55-32 (CANH) - B48-12 (E1)
    R - W-B
    Ignition switch off
    200 Ω or higher
    D55-31 (CANL) - B48-12 (E1)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D55-32 (CANH) - D56-24 (BATT)
    R - R
    Negative battery terminal disconnected
    6 kΩ or higher
    D55-31 (CANL) - D56-24 (BATT)
    W - R
    Negative battery terminal disconnected
    6 kΩ or higher


AIR CONDITIONING AMPLIFIER
C152868E05
  1. Disconnect the connector from the air conditioning amplifier.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    D33-11 (CANH) - D33-12 (CANL)
    LG - W (LHD)
    P - W (RHD)
    Ignition switch off
    54 to 69 Ω
    D33-11 (CANH) - D33-14 (GND)
    LG - W-B (LHD)
    P - W-B (RHD)
    Ignition switch off
    200 Ω or higher
    D33-12 (CANL) - D33-14 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D33-11 (CANH) - D33-21 (B)
    LG - LG (LHD)
    P - LG (RHD)
    Negative battery terminal disconnected
    6 kΩ or higher
    D33-12 (CANL) - D33-21 (B)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


COMBINATION METER

  1. C229505E03
    Disconnect the connector from the combination meter.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    E1-25 (CANH) - E1-26 (CANL)
    P - W
    Ignition switch off
    108 to 132 Ω
    E1-25 (CANH) - E1-20 (ES)
    P - W-B
    Ignition switch off
    200 Ω or higher
    E1-26 (CANL) - E1-20 (ES)
    W - W-B
    Ignition switch off
    200 Ω or higher
    E1-25 (CANH) - E1-21 (B)
    P - SB
    Negative battery terminal disconnected
    6 kΩ or higher
    E1-26 (CANL) - E1-21 (B)
    W - SB
    Negative battery terminal disconnected
    6 kΩ or higher


MAIN BODY ECU
  1. Disconnect the connector from the main body ECU.

  2. C195603E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    D8-5 (CANH) - D8-6 (CANL)
    GR - W
    Ignition switch off
    54 to 69 Ω
    D8-5 (CANH) - D43-4 (CG)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    D8-6 (CANL) - D43-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D8-5 (CANH) - D43-16 (BAT)
    GR - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D8-6 (CANL) - D43-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D8-16 (CANP) - D8-15 (CANN)
    Y - W
    Ignition switch off
    108 to 132 Ω
    D8-16 (CANP) - D43-4 (CG)
    Y - W-B
    Ignition switch off
    200 Ω or higher
    D8-15 (CANN) - D43-4 (CG)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D8-16 (CANP) - D43-16 (BAT)
    Y - LG
    Negative battery terminal disconnected
    6 kΩ or higher
    D8-18 (CANN) - D43-16 (BAT)
    W - LG
    Negative battery terminal disconnected
    6 kΩ or higher


POWER STEERING ECU

  1. C160514E08
    Disconnect the connectors from the power steering ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    D5-2 (CANH) - D5-8 (CANL)
    B - W (LHD)
    L - W (RHD)
    Ignition switch off
    54 to 69 Ω
    D5-2 (CANH) - D4-2 (PGND)
    B - W (LHD)
    L - W (RHD)
    Ignition switch off
    200 Ω or higher
    D5-8 (CANL) - D4-2 (PGND)
    W - W
    Ignition switch off
    200 Ω or higher
    D5-2 (CANH) - D4-1 (PIG)
    B - B (LHD)
    L - B (RHD)
    Negative battery terminal disconnected
    6 kΩ or higher
    D5-8 (CANL) - D4-1 (PIG)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


CERTIFICATION ECU (w/ Smart Entry and Start System)

  1. C152870E07
    Disconnect the connector from the certification ECU.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    D36-27 (CANH) - D36-28 (CANL)
    GR - W
    Ignition switch off
    108 to 132 Ω
    D36-27 (CANH) - D36-17 (E)
    GR - W-B
    Ignition switch off
    200 Ω or higher
    D36-28 (CANL) - D36-17 (E)
    W - W-B
    Ignition switch off
    200 Ω or higher
    D36-27 (CANH) - D36-1 (+B)
    GR - B
    Negative battery terminal disconnected
    6 kΩ or higher
    D36-28 (CANL) - D36-1 (+B)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher


BACK DOOR ECU (w/ Power Back Door System)

  1. C169769E04
    Disconnect the back door ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Terminal
    Wiring Color
    Condition
    Specified Condition
    O14-6 (MPX1) - O14-5 (MPX2)
    B - W
    Ignition switch off
    54 to 69 Ω
    O14-6 (MPX1) - O14-11 (GND)
    B - W-B
    Ignition switch off
    200 Ω or higher
    O14-5 (MPX2) - O14-11 (GND)
    W - W-B
    Ignition switch off
    200 Ω or higher
    O14-6 (MPX1) - O14-12 (B)
    B - B
    Negative battery terminal disconnected
    6 kΩ or higher
    O14-5 (MPX2) - O14-12 (B)
    W - B
    Negative battery terminal disconnected
    6 kΩ or higher

← TERMINALS OF ECU (Jul 2010 – Jun 2012)DIAGNOSIS SYSTEM (May 2007 – Jul 2008) →