2007-2013 Highlander Kluger · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE ENGINE UNDER COVER ASSEMBLY

  1. A171849
    Remove the 2 bolts and engine under cover assembly RR.

  1. A171850
    Remove the 2 bolts, 2 screws, 5 clips and engine under cover assembly.


2. REMOVE NO. 1 ENGINE UNDER COVER

  1. A171855
    Remove the 6 bolts, 2 clips and No. 1 engine under cover.


3. REMOVE FRONT FENDER MOULDING SUB-ASSEMBLY LH

  1. B172795
    Remove the clip.

  1. Using a 4 mm hexagon wrench, remove the screw.

  1. B172796
    Peel off the front fender side protector and disengage the 3 clips, and then remove the front fender moulding sub-assembly.

  1. Remove the pad from the front fender moulding sub-assembly.

  1. Remove the 2 No. 4 clips from the front fender moulding sub-assembly.

  1. B172797E01
    Remove the front fender side protector from the front fender moulding sub-assembly.


4. REMOVE FRONT FENDER LINER LH

  1. B175996E01
    Remove the screw.

  1. Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.

  1. B174749
    Using a 4 mm hexagon wrench, remove the 2 screws.

  1. Remove the 2 grommets.

    HINT:
    The grommets need to be replaced with new ones because they will break when they are removed.

  1. B174751
    Remove the 5 clips, 8 screws and front fender liner LH.


5. REMOVE COOL AIR INTAKE DUCT SEAL

  1. B172745
    Remove the 11 clips and cool air intake duct seal.


6. REMOVE RADIATOR GRILLE

  1. B172749E01
    Put protective tape around the radiator grille.

  1. B172746
    Remove the 2 bolts and 4 clips.

  1. B172747
    Disengage the 6 claws and 4 guides, and remove the radiator grille.


7. REMOVE HOOD LOCK ASSEMBLY (w/o Engine Hood Courtesy Switch)

  1. B174188
    Remove the hood lock nut cap.

  1. B174189
    Remove the 3 bolts.

  1. B174190
    Disconnect the hood lock control cable and remove the hood lock assembly.


8. REMOVE HOOD LOCK ASSEMBLY (w/ Engine Hood Courtesy Switch)

  1. B174191
    Disconnect the connector.

  1. B174192
    Remove the hood lock nut cap.

  1. B174193
    Remove the 3 bolts.

  1. B174194
    Disconnect the hood lock control cable and remove the hood lock assembly.


9. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY

  1. B174196
    Disconnect the hood lock control cable from the hood lock control lever.

  1. Using a screwdriver, disconnect the clamps shown in the illustration.

    B174195E01

    Area
    Part Name
    Area
    Part Name
    A
    Hood lock control cable
    E
    Fender liner
    B
    Clamp
    F
    Hood stopper rubber
    C
    Hood cable grommet
    G
    Front washer hose
    D
    Wire harness
    H
    Rear washer hose

    HINT:
    Tape the screwdriver tip before use.

  1. Pull the cable from the engine compartment and remove it.

← REMOVAL (May 2007 – Jul 2008)REMOVAL (from Jul 2010) →