2007-2013 Highlander Kluger · Service Manual STEERING

B2782 Power Source Control ECU Malfunction

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The steering lock ECU activates the steering lock motor by the power from the main body ECU (*) through the IGE circuit. This prevents the steering from being locked while the vehicle is moving.
The diagnosis information of the steering lock ECU is transmitted to the tester via the certification ECU (smart key ECU assembly) as the steering lock ECU is not connected to the CAN communication system.

HINT:
*: The power source control ECU is not a physical part. This code refers to the power source control function performed by the main body ECU.

DTC No.
DTC Detecting Condition
Trouble Area
B2782
Steering lock motor drive control circuit is defective.
  1. Wire harness
  2. Steering lock actuator assembly (Steering lock ECU)
  3. Main body ECU

WIRING DIAGRAM

C113485E15

INSPECTION PROCEDURE

When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following step to wake up the ECU:
Before starting the inspection, with the engine switch off, open the driver's door. Then (with the engine switch still off) open and close any door several times in 1.5-second intervals.

NOTICE:
If the steering lock actuator assembly (steering lock ECU) is replaced, with the engine switch off and the shift lever in the N position, open and close the driver's door to record the current lock position into the steering lock ECU. If this is not performed, the engine may not start.


1. INSPECT STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)

  1. C157849E12
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D10-3 (IGE) - D10-1 (GND)
    The specified condition should be checked after performing the following:
    1. Turn the engine switch off
    2. Turn the engine switch on (ACC or IG)
    1. Motor activated: Below 1 V
    2. Motor not activated: 11 to 14 V
    D10-3 (IGE) - D10-1 (GND)
    The specified condition should be checked after performing the following:
    1. Move the shift lever to the P position
    2. Turn the engine switch off
    3. Open the driver's door
    1. Motor activated: Below 1 V
    2. Motor not activated: 11 to 14 V

    HINT:
    The steering lock ECU and steering lock actuator assembly are supplied as a unit.



NG
Go to step 2
OK

REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)

2. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - BODY GROUND)

  1. C157850E12
    Disconnect the D10 connector from the steering lock actuator assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D10-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (STEERING LOCK ACTUATOR ASSEMBLY - MAIN BODY ECU)

  1. C157851E09
    Disconnect the D7 connector from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    D10-3 (IGE) - D7-19 (SLR+)
    Always
    Below 1 Ω
    D10-3 (IGE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← B2781 Open / Short in Steering Lock ECU (from Jul 2010)B2782 Power Source Control ECU Malfunction (Aug 2008 – Jun 2010) →