2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1653/35 Seat Position Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly and the seat position airbag sensor.
DTC B1653/35 is recorded when a malfunction is detected in the seat position airbag sensor circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds.
  2. Seat position airbag sensor malfunction
  3. Center airbag sensor assembly malfunction
  1. Floor wire No. 2 (for LHD)
  2. Floor wire (for RHD)
  3. Seat position airbag sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM

C169844E01

INSPECTION PROCEDURE


1. CHECK CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor assembly, front seat inner belt assembly (Driver side) and the seat position airbag sensor.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the center airbag sensor assembly, front seat inner belt assembly and the seat position airbag sensor.

  1. Check that the terminals of connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A


2. CHECK WIRE HARNESS (OPEN)
C169652E01
  1. for LHD:Connect the connectors to the front seat inner belt assembly (Driver side) and floor wire No. 2.

  1. for RHD:Connect the connectors to the front seat inner belt assembly (Driver side) and floor wire.

  1. Using SST, connect terminals 13 (DSP+) and 14 (DSP-) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

SST
09843-18040  
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω



NG
Go to step 9
OK


3. CHECK WIRE HARNESS (SHORT)

  1. C169648E01
    Disconnect SST from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Always
    1 MΩ or higher



NG
Go to step 10
OK


4. CHECK WIRE HARNESS (SHORT TO B+)

  1. C169648E01
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Ignition switch on (IG)
    Below 1 V
    2 - Body ground
    Ignition switch on (IG)
    Below 1 V



NG
Go to step 11
OK


5. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C169648E01
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Always
    1 MΩ or higher
    2 - Body ground
    Always
    1 MΩ or higher



NG
Go to step 12
OK


6. CHECK SEAT POSITION AIRBAG SENSOR

  1. C145343E02
    Connect the connectors to the center airbag sensor assembly and the seat position airbag sensor.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK

7. REPLACE SEAT POSITION AIRBAG SENSOR
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Replace the seat position airbag sensor (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


8. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. C145343E02
    Connect the negative (-) terminal cable to the battery.

  1. Turn the engine switch on (IG), and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch on (IG), and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END

9. CHECK WIRE HARNESS (OPEN)
C157708E02
  1. for LHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (Driver side).

    HINT:
    SST has already been inserted into connector B.

  1. for RHD:Disconnect the floor wire connector from the front seat inner belt assembly (Driver side).

    HINT:
    SST has already been inserted into connector B.

  1. Using SST, connect terminals 14 (DSP+) and 13 (DSP-) of connector B.

    NOTICE:
    Do not forcibly insert SST into the terminals of the connector when connecting the wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-2 (LSP+) - O10-4 (LSP-)
    Always
    Below 1 Ω
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N19-2 (RSP+) - N19-4 (RSP-)
    Always
    Below 1 Ω

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)

10. CHECK WIRE HARNESS (SHORT)

  1. C157709E02
    for LHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (Driver side).

  1. for RHD:Disconnect the floor wire connector from the front seat inner belt assembly (Driver side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-2 (LSP+) - O10-4 (LSP-)
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N19-2 (RSP+) - N19-4 (RSP-)
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)

11. CHECK WIRE HARNESS (SHORT TO B+)

  1. C157709E02
    Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable to the battery.

  1. for LHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (Driver side).

  1. for RHD:Disconnect the floor wire connector from the front seat inner belt assembly (Driver side).

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-2 (LSP+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    O10-4 (LSP-) - Body ground
    Ignition switch on (IG)
    Below 1 V
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N19-2 (RSP+) - Body ground
    Ignition switch on (IG)
    Below 1 V
    N19-4 (RSP-) - Body ground
    Ignition switch on (IG)
    Below 1 V

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)

12. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. C157709E02
    for LHD:Disconnect the floor wire No. 2 connector from the front seat inner belt assembly (Driver side).

  1. for RHD:Disconnect the floor wire connector from the front seat inner belt assembly (Driver side).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Switch Condition
    Specified Condition
    O10-2 (LSP+) - Body ground
    Always
    1 MΩ or higher
    O10-4 (LSP-) - Body ground
    Always
    1 MΩ or higher
    for RHD:
    Tester Connection
    Switch Condition
    Specified Condition
    N19-2 (RSP+) - Body ground
    Always
    1 MΩ or higher
    N19-4 (RSP-) - Body ground
    Always
    1 MΩ or higher

    Result:
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE FLOOR WIRE NO. 2

C
REPLACE FLOOR WIRE
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)


← B1635/24 Front Passenger Side Rear Airbag Sensor Malfunction (Aug 2008 – Jun 2010)B1653/35 Seat Position Airbag Sensor Circuit Malfunction (Aug 2008 – Jun 2010) →