2007-2013 Highlander Kluger · Service Manual RESTRAINTS

B1653/35 Seat Position Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The seat position airbag sensor circuit consists of the center airbag sensor assembly, front seat inner belt assembly (driver side) and seat position airbag sensor.
DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.
DTC No.
DTC Detection Condition
Trouble Area
B1653/35
  1. The center airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position airbag sensor circuit.
  2. Front seat inner belt assembly (driver side)
  3. Seat position airbag sensor malfunction
  4. Center airbag sensor assembly malfunction
for LHD:
  1. No. 2 floor wire
  2. Front seat inner belt assembly LH
  3. Seat position airbag sensor
  4. Center airbag sensor assembly
for RHD:
  1. Floor wire
  2. Front seat inner belt assembly RH
  3. Seat position airbag sensor
  4. Center airbag sensor assembly

WIRING DIAGRAM

C227331E01

INSPECTION PROCEDURE


1. CHECK CONNECTORS
  1. for LHD:

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the center airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.

      OK:
      The connectors are properly connected.

      HINT:
      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the center airbag sensor assembly, front seat inner belt assembly LH and seat position airbag sensor.

    5. Check that the terminals of the connectors are not damaged.

      OK:
      The terminals are not deformed or damaged.

  1. for RHD:

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the center airbag sensor assembly, front seat inner belt assembly RH and seat position airbag sensor.

      OK:
      The connectors are properly connected.

      HINT:
      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the center airbag sensor assembly, front seat inner belt assembly RH and seat position airbag sensor.

    5. Check that the terminals of the connectors are not damaged.

      OK:
      The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


2. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (OPEN)

  1. for LHD:

    1. Connect the connectors to the front seat inner belt assembly LH and No. 2 floor wire.C227327E01

    2. Using SST, connect terminals 14 (LSP+) and 13 (LSP-) of connector B.

      NOTICE:
      Do not forcibly insert SST into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2 (LSP+) - 1 (LSP-)
      Always
      Below 1 Ω

SST
09843-18040  

  1. for RHD:

    1. Connect the connectors to the front seat inner belt assembly RH and floor wire.C227328E01

    2. Using SST, connect terminals 12 (RSP+) and 13 (RSP-) of connector B.

      NOTICE:
      Do not forcibly insert SST into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2 (RSP+) - 1 (RSP-)
      Always
      Below 1 Ω

SST
09843-18040  


NG
Go to step 9
OK


3. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT)

  1. for LHD:

    1. C171042E03
      Disconnect SST from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2 (LSP+) - 1 (LSP-)
      Always
      1 MΩ or higher

  1. for RHD:

    1. C227329E01
      Disconnect SST from connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2 (RSP+) - 1 (RSP-)
      Always
      1 MΩ or higher



NG
Go to step 10
OK


4. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO B+)

  1. for LHD:

    1. C171042E03
      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (LSP+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      1 (LSP-) - Body ground
      Ignition switch on (IG)
      Below 1 V

  1. for RHD:

    1. C227329E01
      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      2 (RSP+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      1 (RSP-) - Body ground
      Ignition switch on (IG)
      Below 1 V



NG
Go to step 11
OK


5. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT (SHORT TO GROUND)

  1. for LHD:

    1. C171042E03
      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2 (LSP+) - Body ground
      Always
      1 MΩ or higher
      1 (LSP-) - Body ground
      Always
      1 MΩ or higher

  1. for RHD:

    1. C227329E01
      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      2 (RSP+) - Body ground
      Always
      1 MΩ or higher
      1 (RSP-) - Body ground
      Always
      1 MΩ or higher



NG
Go to step 12
OK


6. CHECK SEAT POSITION AIRBAG SENSOR

  1. for LHD:

    1. C203081E01
      Connect the connectors to the center airbag sensor assembly and seat position airbag sensor.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the ignition switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs stored in the memory (Click here).

    5. Turn the ignition switch off.

    6. Turn the ignition switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs (Click here).

      OK:
      DTC B1653/35 is not output.

      HINT:
      Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.

  1. for RHD:

    1. C227332E01
      Connect the connectors to the center airbag sensor assembly and seat position airbag sensor.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the ignition switch on (IG), and wait for at least 60 seconds.

    4. Clear the DTCs stored in the memory (Click here).

    5. Turn the ignition switch off.

    6. Turn the ignition switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs (Click here).

      OK:
      DTC B1653/35 is not output.

      HINT:
      Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)

7. REPLACE SEAT POSITION AIRBAG SENSOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the seat position airbag sensor with a known good part (Click here).

    HINT:
    Perform the following inspection using known good parts from another vehicle if possible.


NEXT


8. CHECK CENTER AIRBAG SENSOR ASSEMBLY

  1. for LHD:

    1. C203081E01
      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch on (IG), and wait for at least 60 seconds.

    3. Clear the DTCs stored in the memory (Click here).

    4. Turn the ignition switch off.

    5. Turn the ignition switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs (Click here).

      OK:
      DTC B1653/35 is not output.

      HINT:
      Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.

  1. for RHD:

    1. C227332E01
      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch on (IG), and wait for at least 60 seconds.

    3. Clear the DTCs stored in the memory (Click here).

    4. Turn the ignition switch off.

    5. Turn the ignition switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs (Click here).

      OK:
      DTC B1653/35 is not output.

      HINT:
      Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

END

9. CHECK WIRE HARNESS (OPEN)

  1. for LHD:

    1. Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.C171043E18

      HINT:
      SST has already been inserted into connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O10-2 (LSP+) - O10-4 (LSP-)
      Always
      Below 1 Ω
      Result 
      Result
      Proceed to
      OK
      A
      NG
      B

  1. for RHD:

    1. Disconnect the floor wire from the front seat inner belt assembly RH.C227330E01

      HINT:
      SST has already been inserted into connector B.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      N19-2 (RSP+) - N19-4 (RSP-)
      Always
      Below 1 Ω
      Result 
      Result
      Proceed to
      OK
      C
      NG
      D



B
REPLACE NO. 2 FLOOR WIRE

C
REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (Click here)

D
REPLACE FLOOR WIRE
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)

10. CHECK WIRE HARNESS (SHORT)

  1. for LHD:

    1. C171044E15
      Disconnect the No. 2 floor wire from the front seat belt inner belt assembly LH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O10-2 (LSP+) - O10-4 (LSP-)
      Always
      1 MΩ or higher
      Result 
      Result
      Proceed to
      OK
      A
      NG
      B

  1. for RHD:

    1. C227333E01
      Disconnect the floor wire from the front seat belt inner belt assembly RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      N19-2 (RSP+) - N19-4 (RSP-)
      Always
      1 MΩ or higher
      Result 
      Result
      Proceed to
      OK
      C
      NG
      D



B
REPLACE NO. 2 FLOOR WIRE

C
REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (Click here)

D
REPLACE FLOOR WIRE
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)

11. CHECK WIRE HARNESS (SHORT TO B+)

  1. for LHD:

    1. C171044E15
      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

    4. Connect the cable to the negative (-) battery terminal.

    5. Turn the ignition switch on (IG).

    6. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      O10-2 (LSP+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      O10-4 (LSP-) - Body ground
      Ignition switch on (IG)
      Below 1 V
      Result 
      Result
      Proceed to
      OK
      A
      NG
      B

  1. for RHD:

    1. C227333E01
      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Disconnect the floor wire from the front seat inner belt assembly RH.

    4. Connect the cable to the negative (-) battery terminal.

    5. Turn the ignition switch on (IG).

    6. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      N19-2 (RSP+) - Body ground
      Ignition switch on (IG)
      Below 1 V
      N19-4 (RSP-) - Body ground
      Ignition switch on (IG)
      Below 1 V
      Result 
      Result
      Proceed to
      OK
      C
      NG
      D



B
REPLACE NO. 2 FLOOR WIRE

C
REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (Click here)

D
REPLACE FLOOR WIRE
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)

12. CHECK WIRE HARNESS (SHORT TO GROUND)

  1. for LHD:

    1. C171044E15
      Disconnect the No. 2 floor wire from the front seat inner belt assembly LH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      O10-2 (LSP+) - Body ground
      Always
      1 MΩ or higher
      O10-4 (LSP-) - Body ground
      Always
      1 MΩ or higher
      Result 
      Result
      Proceed to
      OK
      A
      NG
      B

  1. for RHD:

    1. C227333E01
      Disconnect the floor wire from the front seat inner belt assembly RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      N19-2 (RSP+) - Body ground
      Always
      1 MΩ or higher
      N19-4 (RSP-) - Body ground
      Always
      1 MΩ or higher
      Result 
      Result
      Proceed to
      OK
      C
      NG
      D



B
REPLACE NO. 2 FLOOR WIRE

C
REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (Click here)

D
REPLACE FLOOR WIRE
A

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)


← B1653/35 Seat Position Airbag Sensor Circuit Malfunction (Aug 2008 – Jun 2010)B1655/37 Driver Side Seat Belt Buckle Switch Circuit Malfunction (May 2007 – Jul 2008) →