2007-2013 Highlander Kluger · Service Manual TRANSMISSION

INSPECTION

Inspection · Vehicles built from May 2007


INSPECT MULTIPLE DISC CLUTCH HUB

  1. D003829E06
    Using a dial indicator, measure the inside diameter of the forward clutch hub bushing.

    Standard inside diameter:
    23.025 to 23.046 mm (0.9065 to 0.9073 in.)

    Maximum inside diameter:
    23.09 mm (0.9091 in.)

    NOTICE:
    1. Check the contact surface of the bushing in the direct clutch shaft. If any scratch or discoloration is found, replace the direct clutch sub-assembly with a new one.

    If the inside diameter is greater than the maximum, replace the forward clutch hub with a new one.


INSPECT NO. 2 UNDERDRIVE CLUTCH DISC

  1. D009196
    Check if the sliding surfaces of the disc, plate, and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc comes off or discolors, or if a part of the groove is worn, replace all discs.
    2. Before installing new discs, immerse them in ATF for at least 15 minutes.


INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

  1. D003829E01
    Using a dial indicator, measure the inside diameter of the forward clutch hub bushing.

    Standard inside diameter:
    23.025 to 23.046 mm (0.9065 to 0.9073 in.)

    Maximum inside diameter:
    23.09 mm (0.9091 in.)

    NOTICE:
    1. Check the contact surface of the bushing in the direct clutch shaft. If any scratch or discoloration is found, replace the direct clutch sub-assembly with a new one.

    If the inside diameter is greater than the maximum, replace the forward clutch hub with a new one.


INSPECT 2ND BRAKE CLUTCH DISC

  1. D026717
    Check if the sliding surface of the disc, plate, and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc comes off or discolors, or if a part of the groove is worn, replace all discs.
    2. Before installing new discs, immerse them in ATF for at least 15 minutes.


INSPECT 1ST AND REVERSE BRAKE CLUTCH DISC

  1. D009189
    Check if the sliding surface of the disc, plate, and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the lining of the disc comes off or discolors, or if a part of the groove is worn, replace all discs.
    2. Before installing new discs, immerse them in ATF for at least 15 minutes.


INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. C161144E02
    Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.61 mm (0.6933 in.)

    HINT:
    If the result is not as specified, replace the spring.


INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D030852E11
    Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    13.24 mm (0.5213 in.)

    HINT:
    If the result is not as specified, replace the spring.


INSPECT PACK CLEARANCE OF 1ST AND REVERSE BRAKE

  1. D026452E01
    Using vernier calipers, measure the distance between the disc surface and the contact surface of the 2nd brake cylinder and transaxle case (Dimension A).

  1. Select an appropriate flange so that the pack clearance will be within the specified range.

    Pack clearance:
    1.16 to 1.35 mm (0.0457 to 0.0531 in.)

    HINT:
    Piston stroke = Dimension A - Flange thickness

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    1
    1.8 (0.071)
    5
    2.2 (0.087)
    2
    1.9 (0.075)
    6
    2.3 (0.091)
    3
    2.0 (0.079)
    7
    2.4 (0.094)
    4
    2.1 (0.083)
    8
    2.5 (0.098)

  1. Install the flange.


INSPECT PACK CLEARANCE OF 2ND BRAKE

  1. D026453E01
    Using vernier calipers, measure the distance between the disc surface and snap ring surface (Dimension B).

  1. Select an appropriate flange so that the pack clearance will be within the specified range.

    Pack clearance:
    0.62 to 0.91 mm (0.0244 to 0.0358 in.)

    HINT:
    Piston stroke = Dimension B - Flange thickness - Snap ring thickness 1.6 mm (0.063 in.)

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    1
    3.0 (0.118)
    5
    3.4 (0.134)
    2
    3.1 (0.122)
    6
    3.5 (0.138)
    3
    3.2 (0.126)
    7
    3.6 (0.142)
    4
    3.3 (0.130)
    8
    -


INSPECT PACK CLEARANCE OF UNDERDRIVE BRAKE

  1. D008082
    Using a dial indicator, measure the underdrive brake pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Pack clearance:
    1.81 to 2.20 mm (0.0713 to 0.0866 in.)

    HINT:
    Select an appropriate flange from the table below so that it will be within the specified range.

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    1
    3.0 (0.118)
    4
    3.1 (0.122)
    2
    3.2 (0.126)
    5
    3.3 (0.130)
    3
    3.4 (0.134)
    -
    -

  1. Temporarily remove the snap ring and attach it to the flange.

  1. Reinstall the snap ring.


INSPECT UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY

  1. D003925E01
    Install the underdrive clutch assembly to the one-way clutch.

  1. Rotate the underdrive one-way clutch assembly to check the rotating direction for the lock or free operation.

    HINT:
    If the result is not as specified, replace the underdrive one-way clutch.


INSPECT INPUT SHAFT END PLAY

  1. D008091
    Using a dial indicator, measure the input shaft end play.

    End play:
    0.262 to 1.244 mm (0.0103 to 0.0490 in.)

    HINT:
    If the result is not as specified, replace the input shaft or thrust needle roller bearing.

← DISASSEMBLY (from May 2007)REASSEMBLY (from May 2007) →