2007-2013 Highlander Kluger · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from May 2007


1. BEARING POSITION

C110530E01
Mark
Front Race Diameter
Inside / Outside mm (in.)
Thrust Bearing Diameter
Inside / Outside mm (in.)
Rear Race Diameter
Inside / Outside mm (in.)
A
-
57.2 (2.252) / 84.96 (3.3449)
56.4 (2.220) / 83.0 (3.268)
B
-
37.73 (1.4854) / 58.0 (2.283)
-
C
-
33.85 (1.3327) / 52.2 (2.055)
-
D
24.94 (0.9820)
23.5 (0.925) / 44.0 (1.732)
-
E
-
36.3 (1.429) / 51.93 (2.0445)
34.5 (1.358) / 48.35 (1.9035)
F
34.35 (1.3526) / 56.57 (2.2271)
32.45 (1.2776) / 56.48 (2.2236)
-
G
40.15 (1.5807) / 59.25 (2.3327)
38.65 (1.5217) / 59.79 (2.3539)
38.65 (1.5217) / 59.25 (2.3327)
H
-
53.6 (2.110) / 69.6 (2.740)
-
I
33.02 (1.3000) / 45.8 (1.803)
31.85 (1.2539) / 57.3 (2.256)
-
J
-
24.79 (0.976) / 39.5 (1.555)
23.6 (0.929) / 37.95 (1.4941)
K
-
56.3 (2.217) / 75.96 (2.9905)
-

2. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

  1. D026400E08
    Install the differential gear lube apply tube and transaxle apply tube clamp to the transaxle housing with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

    NOTICE:
    Make sure to insert the pipe to the stopper.


3. INSTALL NO. 1 TRANSAXLE CASE PLUG

  1. D026383
    Install 2 new O-rings to the 2 No. 1 transaxle case plugs.

  1. Install the 2 No. 1 transaxle case plugs to the transaxle rear cover.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


4. INSTALL UNDERDRIVE OUTPUT SHAFT OIL SEAL RING

  1. D003915E11
    Coat a new oil seal ring with ATF and install it to the transaxle housing.


5. INSTALL UNDERDRIVE CYLINDRICAL ROLLER BEARING

  1. D003807E01
    Coat the underdrive cylindrical roller bearing with ATF.

  1. Using SST and a press, install the underdrive cylindrical roller bearing.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07100)

    NOTICE:
    Do not apply excessive pressure to the bearing.


6. INSTALL UNDERDRIVE CLUTCH DRUM OIL SEAL RING

  1. D003914E10
    Coat 2 new oil seal rings with ATF and install them to the transaxle rear cover.

    NOTICE:
    1. Do not expand the end gap of the oil seal ring too much.
    2. Secure the hooks firmly. Confirm that the oil seal ring rotates freely in its groove.


7. INSTALL NEEDLE ROLLER BEARING

  1. D003809E01
    Wrap vinyl tape around SST 4.0 mm (0.157 in.) from the bottom of SST until the thickness of the tape is approximately 5.0 mm (0.197 in.).
    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    Clean SST to remove deposited oil before wrapping vinyl tape.

  1. Coat the needle roller bearing with ATF.

  1. D003810E01
    Using SST and a press, install the needle-roller bearing to the transaxle case.
    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    When the wrapped vinyl tape contacts the transaxle case, stop press-fitting.


8. INSTALL UNDERDRIVE BRAKE PISTON

  1. D003794E04
    Coat 2 new O-rings with ATF and install them to the underdrive brake piston.

    NOTICE:
    1. Make sure that the O-rings are not twisted or pinched when they are installed.
    2. Apply sufficient ATF to the O-ring before installing.

  1. Coat the underdrive brake piston with ATF.

  1. D026764E03
    Install the underdrive brake piston to the transaxle case.

    NOTICE:
    Be careful not to damage the O-ring.


9. INSTALL UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D026407E01
    Place SST on the return spring and compress the return spring with a press.
    SST
    09387-00020  

  1. Using a snap ring expander, install the snap ring to the transaxle case.

    NOTICE:
    1. Stop the press when the spring seat is lowered 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.
    3. Install the spring sub-assembly and check that all of the springs are fully engaged in the piston correctly.
    4. The snap ring should be fully engaged in the groove of the transaxle case.


10. INSTALL NO. 2 BREATHER PLUG

11. INSTALL COUNTER DRIVE GEAR BEARING

  1. C089126E01
    Coat the counter drive gear bearing with ATF.

  1. Using SST and a press, install the bearing outer race.

    SST
    09950-60020   (09951-01030)
    09950-70010   (09951-07150)
    09649-17010  

    NOTICE:
    1. Do not apply excessive pressure to the bearing.
    2. Press-fit the bearing outer race until it contacts the transaxle case.

  1. D026467E01
    Using a snap ring expander, install the snap ring.

    NOTICE:
    The surface with a white mark of the snap ring should face upward.


12. INSTALL COUNTER DRIVE GEAR

  1. D026410E01
    Coat the counter drive gear with ATF.

  1. Using SST and a press, install the tapered roller bearing to the counter drive gear.

    SST
    09950-70010   (09951-07150)
    09649-17010  

    NOTICE:
    Do not apply excessive pressure to the bearing.

  1. C161145E02
    Using SST and a press, install the counter drive gear and bearing to the transaxle case.
    SST
    09950-70010   (09951-07150)
    09223-15030  
    09527-17011  
    09950-60020   (09951-00750)

    NOTICE:
    Do not apply excessive pressure to the counter drive gear.


13. INSTALL 1ST AND REVERSE BRAKE PISTON

  1. D026713E03
    Coat 2 new O-rings with ATF.

  1. Install the 2 O-rings to the 1st and reverse brake piston.

    NOTICE:
    1. Make sure that the O-rings are not twisted or pinched when they are installed.
    2. Apply sufficient ATF to the O-rings before assembling them.

  1. D026593E01
    Coat the 1st and reverse brake piston with ATF and install it to the transaxle case.

    NOTICE:
    Be careful not to damage the O-ring.


14. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D003600E01
    Place SST on the return spring and compress the return spring with a press.
    SST
    09387-00070  

  1. Using a snap ring expander, install the snap ring to the transaxle case.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.
    3. Install the spring sub-assembly and check that all of the springs are fit in the piston correctly.
    4. The snap ring should be fully engaged in the groove of the cylinder.
    5. Fix the snap ring to the inside of the claw of the spring seat firmly.


15. INSTALL FRONT PLANETARY RING GEAR

  1. D003615E06
    Using a screwdriver, install the front planetary ring gear and snap ring to the brake hub.

    NOTICE:
    Confirm that the snap ring is engaged in the groove of the brake hub correctly.


16. INSTALL FRONT PLANETARY GEAR ASSEMBLY

  1. D026763E01
    Install the front planetary gear assembly to the brake hub.

  1. D003916E05
    Using SST and a press, press-fit the front planetary gear assembly.
    SST
    09950-60010   (09951-00500)
    09950-70010   (09951-07100)

    NOTICE:
    1. Do not apply excessive pressure to the planetary gear assembly.
    2. Press the inner race of the LH tapered roller bearing, counter gear and front planetary gear assembly to the position where no pre-load should be applied to one pair of the tapered roller bearings (left and right).

  1. D003917
    Install a new washer as shown in the illustration.

  1. D003596E01
    Using SST, install the nut.
    SST
    09387-00030  
    09387-00080  

    Torque:
    280 N*m{ 2854 kgf*cm , 207 ft.*lbf }

    NOTICE:
    Assemble the washer after pressing each part, then tighten the nut to the minimum tightening torque.

  1. D003918E01
    Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm. When the measured value is not as specified, gradually tighten the nut until it reaches the specified value.
    SST
    09387-00080  

    Standard:
    Turning torque at 60 rpm

    Bearing:
    New Bearing:
    0.51 to 1.02 N*m (5.1 to 10.0 kgf*cm, 4.4 to 8.7 in.*lbf)
    Used Bearing:
    0.26 to 0.51 N*m (2.7 to 5.2 kgf*cm, 2.3 to 4.5 in.*lbf)

    HINT:
    Use a torque wrench with a fulcrum length of 160 mm (6.3 in.).

  1. Tighten the nut gradually until the specified turning torque of the tapered roller bearing is measured.

    Torque:
    350 N*m{ 3569 kgf*cm , 258 ft.*lbf }

  1. D008074E01
    Using a chisel and hammer, stake the front lock washer.


17. INSTALL INPUT SUN GEAR

  1. C134855E02
    Coat the 2 thrust bearings with ATF.

  1. Install the 2 thrust bearings, the 3 bearing races, and the input sun gear to the transaxle case.

    NOTICE:
    1. Install the bearing race on the side of the front planetary carrier. Make sure that the race is installed in the correct direction.
    2. When installing the thrust bearing and front sun gears, make sure that they are installed in the correct direction.
    3. Install the bearing race on the side of the front sun gear. Make sure that the race is installed in the correct direction.
    4. Install the thrust bearing and the race after holding the parts on the input sun gear by applying grease. Make sure that the assembling order is correct.

    Thrust bearing and bearing race diameter: mm (in.) 

    Inside
    Outside
    Bearing Race, A
    34.5 (1.358)
    56.82 (2.2370)
    Thrust Bearing, B
    32.4 (1.276)
    56.62 (2.2291)
    Bearing Race, C
    40.3 (1.587)
    58.0 (2.284)
    Thrust Bearing, D
    40.3 (1.587)
    58.1 (2.287)
    Bearing Race, E
    38.6 (1.520)
    58.0 (2.284)


18. INSTALL REAR PLANETARY GEAR ASSEMBLY

  1. D026591E06
    Install the rear planetary gear assembly to the rear planetary ring gear.

  1. D003616E01
    Using a screwdriver, install the snap ring.

    NOTICE:
    Confirm that the snap ring is engaged in the groove of the 1st and reverse brake hub correctly.


19. INSTALL 1ST AND REVERSE BRAKE CLUTCH DISC

  1. D026413E02
    Coat the 6 discs with ATF.

  1. Install the 6 plates and 6 discs.

    NOTICE:
    Make sure that the plates, discs, and flange are installed as shown in the illustration.


20. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE

  1. D026452E01
    Using vernier calipers, measure the distance between the disc surface and the contact surface of the 2nd brake cylinder and transaxle case (Dimension A).

  1. Select an appropriate flange so that the pack clearance will be within the specified range.

    Pack clearance:
    1.16 to 1.35 mm (0.0457 to 0.0531 in.)

    HINT:
    Piston stroke = Dimension A - Flange thickness

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    1
    1.8 (0.071)
    5
    2.2 (0.087)
    2
    1.9 (0.075)
    6
    2.3 (0.091)
    3
    2.0 (0.079)
    7
    2.4 (0.094)
    4
    2.1 (0.083)
    8
    2.5 (0.098)

  1. D003815
    Install the flange.


21. INSTALL 2ND BRAKE PISTON ASSEMBLY

  1. D026396E07
    Install the 2nd brake piston assembly to the transaxle case.

  1. D008058E01
    Install the snap ring and measure the inside diameter.

    Inside diameter:
    Greater than 167 mm (6.57 in.)

    NOTICE:
    1. Make sure that the tapered snap ring is installed in the correct direction.
    2. When the diameter is not as specified, replace the snap ring with a new one.
    3. After installing, confirm that there is no clearance between the 2nd brake cylinder and the fitting surface of the cylinder in the transaxle case.


22. INSTALL ONE-WAY CLUTCH SLEEVE OUTER

  1. C092977E03
    Install the one-way clutch sleeve outer to the 2nd brake cylinder assembly.

    NOTICE:
    Make sure that the outer sleeve is installed in the correct direction.


23. INSTALL ONE-WAY CLUTCH ASSEMBLY

  1. D003909E06
    Install the one-way clutch inner race to the one-way clutch.

    NOTICE:
    1. Make sure that the inner race is installed in the correct direction.
    2. Confirm that the discrimination mark can be seen.

  1. D009638E01
    Check the rotating direction of one-way clutch for the lock or free operation as shown in the illustration.

  1. D003588E05
    Install the one-way clutch and thrust needle roller bearing to the one-way clutch sleeve outer.
    Bearing diameter: mm (in.) 

    Inside
    Outside
    Bearing
    53.6 (2.110)
    69.4 (2.732)

    NOTICE:
    Install the thrust bearing properly so that no-colored race can be seen.


24. INSTALL NO. 1 PLANETARY CARRIER THRUST WASHER

  1. D026394E05
    Coat the No. 1 planetary carrier thrust washer with yellow petrolatum, and install the washer onto the planetary sun gear assembly.

    NOTICE:
    After installing, confirm that the projection should be firmly engaged in the hole of the planetary sun gear assembly.


25. INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

  1. D026393E04
    Coat the No. 2 planetary carrier thrust washer with yellow petrolatum, and install the washer onto the rear planetary sun gear.

  1. D026404E09
    Coat the bearing with yellow petrolatum, and install the bearing onto the rear planetary sun gear.
    Bearing diameter: mm (in.) 

    Inside
    Outside
    Race, A
    33.0 (1.299)
    45.4 (1.787)
    Bearing, B
    31.85 (1.254)
    45.2 (1.78)

  1. D026714E07
    Install the rear planetary sun gear assembly to the rear planetary gear.

    NOTICE:
    After installing the rear planetary sun gear assembly, make sure that the B1 discs are engaged.


26. INSTALL 2ND BRAKE CLUTCH DISC

  1. D026412E02
    Coat the 4 discs with ATF.

  1. Install the 4 discs and 4 plates to the transaxle case.

  1. Temporarily install the snap ring.


27. INSPECT PACK CLEARANCE OF 2ND BRAKE

  1. D026453E01
    Using vernier calipers, measure the distance between the disc surface and snap ring surface (Dimension B).

  1. Select an appropriate flange so that the pack clearance will be within the specified range.

    Clearance:
    0.62 to 0.91 mm (0.0244 to 0.0358 in.)

    HINT:
    Piston stroke = Dimension B - Flange thickness - Snap ring thickness 1.6 mm (0.063 in.)

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    1
    3.0 (0.118)
    5
    3.4 (0.134)
    2
    3.1 (0.122)
    6
    3.5 (0.138)
    3
    3.2 (0.126)
    7
    3.6 (0.142)
    4
    3.3 (0.130)
    8
    -

  1. D003623E01
    Temporarily remove the snap ring, attach the selected flange, and reinstall the snap ring.

    NOTICE:
    Secure the snap ring so that the ends can be seen through the groove of the transaxle case.


28. INSTALL OVERDRIVE DIRECT CLUTCH HUB SUB-ASSEMBLY

  1. D026392E08
    Install the direct clutch hub to the planetary gear assembly.

    NOTICE:
    Be careful not to damage the bushing inside the overdrive clutch hub during installation.

  1. Coat the thrust bearing with ATF.

  1. Install the bearing race and the thrust bearing to the direct clutch hub.

    NOTICE:
    Be careful not to drop the bearing when it is installed.

    Bearing and race diameter: mm (in.) 

    Inside
    Outside
    Bearing, A
    24.7 (0.972)
    39.5 (1.555)
    Race, B
    23.6 (0.929)
    38.0 (1.496)


29. INSTALL DIRECT CLUTCH ASSEMBLY

  1. D026403E05
    Coat the thrust bearing with ATF.

  1. Install the direct clutch assembly and thrust bearing to the rear planetary sun gear assembly.

    NOTICE:
    The disc in the direct clutch should completely match with the hub attached outside the rear planetary sun gear. Otherwise, the rear cover cannot be installed.

  1. D026469E01
    Clean the connecting part of the transaxle case and the rear cover.

  1. As shown in the illustration, place a straightedge on the direct clutch drum and measure the distance between the transaxle case and the straightedge using vernier calipers (Dimension C).

  1. D026470E01
    Using vernier calipers and a straightedge, measure the dimension shown in the illustration.

  1. Calculate the end play using the following formula. Select a thrust bearing which satisfies the end play and install the selected bearing.

    End play:
    0.244 to 0.901 mm (0.0096 to 0.0355 in.)

    NOTICE:
    Make sure that the no-colored race side is facing the direct clutch assembly.

    HINT:
    End play = Dimension D - Dimension C

    Bearing thickness and diameter : mm (in.) 
    Thickness
    Inside
    Outside
    3.6 (0.1417)
    56.3 (2.217)
    75.7 (2.980)
    3.8 (0.1496)
    56.3 (2.217)
    75.7 (2.980)


30. INSTALL NO. 1 GOVERNOR APPLY GASKET

  1. D026390
    Install 3 new No. 1 governor apply gaskets to the transaxle case.


31. INSTALL BRAKE APPLY TUBE

  1. D003923E02
    Install the clamp to the brake apply tube.

    NOTICE:
    Make sure to install the clamp to the apply tube before installing the apply tube to the transaxle case. This prevents the apply tube from being deformed or damaged.

  1. Install the clutch apply tube.

  1. D026391E03
    Install the brake apply tube and a bolt to the transaxle case.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    NOTICE:
    The tube should be securely inserted until it reaches the stopper.


32. INSTALL NEEDLE ROLLER BEARING

  1. D026766E01
    Using SST and a press, press the needle roller bearing into the transaxle rear cover.
    SST
    09950-60010   (09951-00230, 09952-06010)

    Press fit depth:
    20.55 to 21.25 mm (0.8091 to 0.8366 in.)

    NOTICE:
    1. The engraved mark side of the bearing should face upward.
    2. Repeat press fitting until the specified value is obtained.

  1. Coat a needle roller bearing with ATF.


33. INSTALL REAR CLUTCH OIL SEAL RING OUTER

  1. D026389E01
    Coat 3 new rear clutch oil seal rings with ATF, and install them to the transaxle rear cover.

    NOTICE:
    The snap ring should be fully engaged in the groove of the drum.


34. INSTALL NO. 1 TRANSAXLE CASE PLUG

  1. D026388
    Coat 4 new O-rings with ATF.

  1. Install the 4 O-rings to the 4 No. 1 transaxle case plugs.

  1. Install the 4 No. 1 transaxle case plugs to the transaxle rear cover.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


35. INSTALL TRANSAXLE REAR COVER SUB-ASSEMBLY

  1. D026454E02
    Remove any packing material and be careful not to spill oil on the contact surfaces of the transaxle rear cover or the transaxle case.

  1. Apply seal packing to the cover.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    Make sure that the seal packing is applied in a bead (section diameter: φ1.2) so that the entire sealing surface will be evenly sealed. The seal packing should also protrude slightly from the flange after the assembly of the parts has been completed.

  1. D026387E03
    Apply liquid sealer to the "A" bolt threads.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. Install the 11 bolts.

    Torque:
    Bolt A:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }
    Other bolts::
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }


36. INSTALL NO. 2 UNDERDRIVE CLUTCH DISC

  1. D026414E01
    Coat the 4 discs with ATF.

  1. Install the 4 discs, 4 plates, and flange to the transaxle case.

    NOTICE:
    Make sure that discs, plate, and flange assembly are installed in the correct order.

  1. D026466E01
    Using a screwdriver, install the snap ring.

    NOTICE:
    The snap ring should be fully engaged in the groove of the drum.


37. INSPECT PACK CLEARANCE OF UNDERDRIVE BRAKE

  1. D008082
    Using a dial indicator, measure the underdrive brake pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Pack clearance:
    1.81 to 2.20 mm (0.0713 to 0.0866 in.)

    HINT:
    Select an appropriate flange from the table below so that it will be within the specified range.

    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    1
    3.0 (0.118)
    4
    3.1 (0.122)
    2
    3.2 (0.126)
    5
    3.3 (0.130)
    3
    3.4 (0.134)
    -
    -

  1. Temporarily remove the snap ring and attach it to the flange.

  1. Reinstall the snap ring.


38. INSPECT UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY

  1. D003925E01
    Install the underdrive clutch assembly to the one-way clutch.

  1. Rotate the underdrive clutch assembly to check the rotating direction for the lock or free operation.


39. INSTALL UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY

  1. D003907E03
    Install the outer race retainer to the one-way clutch.

    NOTICE:
    Secure the outer race retainer to the external tooth of the one-way clutch firmly.

  1. D003627E02
    Install the one-way clutch to the transaxle case.

    NOTICE:
    Make sure that the mark on the one-way clutch outer race can be seen.

  1. D003581E01
    Using a screwdriver, install the snap ring to the transaxle case.

    NOTICE:
    The snap ring should be fully engaged in the groove of the transaxle case.


40. INSTALL UNDERDRIVE CLUTCH ASSEMBLY

  1. D003580
    Coat the bearing and bearing race with petroleum jelly, and install them onto the underdrive clutch.
    Bearing and bearing race diameter: mm (in.) 

    Inside
    Outside
    Bearing
    37.73 (1.4854)
    58.0 (2.2835)
    Race
    29.9 (1.1772)
    55.5 (2.185)

  1. Install the underdrive clutch assembly to the transaxle case.

    NOTICE:
    Do not damage the oil seal when installing the underdrive clutch drum sub-assembly.


41. INSTALL PARKING LOCK PAWL

  1. D009691E01
    Install the pawl pin and spring to the parking lock pawl.

  1. D026386
    Temporarily install the parking lock pawl, shaft, and spring to the transaxle case as shown in the illustration.


42. INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY

  1. D003579E06
    Install the underdrive planetary gear assembly to the transaxle case.

    NOTICE:
    1. Fully engage all the discs of the underdrive clutch and hub splines of the underdrive planetary gear assembly and install them securely.
    2. Check the number and position of the gear teeth.

  1. D009693
    Install the parking lock pawl shaft.

  1. D003576E05
    Install the pawl shaft clamp with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. D003875E01
    Using a straightedge and vernier calipers as shown in the illustration, measure the gap between the top of the differential drive pinion in the underdrive planetary gear and the contact surface of the transaxle case and housing (Dimension E).

    NOTICE:
    Record dimension E for the following process.

  1. D025511E01
    As shown in the illustration, measure the 2 places of the transaxle housing, and calculate dimension F using the formula below.

    NOTICE:
    Record dimension F for the following process.

    HINT:
    Dimension F = Dimension (1) - Dimension (2)


43. INSTALL MULTIPLE DISC CLUTCH HUB

  1. D008087E08
    Install the No. 1 thrust bearing race to the transaxle case while checking its direction.
    Bearing race diameter: mm (in.) 

    Inside
    Outside
    Bearing race
    39.5 (1.555)
    45.8 (1.803)

  1. D026710E06
    Coat the thrust needle roller bearing and race with yellow petrolatum, and install them onto the multiple disc clutch hub.
    Thrust bearing and race diameter: mm (in.) 

    Inside
    Outside
    Thrust Bearing
    36.4 (1.433)
    52.2 (2.055)

  1. Coat the needle roller bearing with ATF.

  1. D026711E05
    Install the needle roller bearing to the multiple clutch hub.
    Bearing diameter: mm (in.) 

    Inside
    Outside
    Bearing
    23.6 (0.929)
    44 (1.732)

  1. Install the multiple clutch hub to the transaxle case.


44. INSTALL FORWARD CLUTCH ASSEMBLY

  1. D003820E03
    Coat the thrust needle roller bearing with ATF.

  1. Install the thrust needle roller bearing to the forward clutch.

    Thrust bearing diameter: mm (in.) 

    Inside
    Outside
    Thrust Bearing
    33.58 (1.3220)
    51.9 (2.043)

    NOTICE:
    Install the thrust bearing properly so that the no-colored race or blue ink jet race can be seen.

  1. D003574E04
    Install the forward clutch to the forward clutch assembly.

    NOTICE:
    1. Align the splines of all discs in the forward clutch with those of multiple clutch hub to install them securely.
    2. Be careful not to damage the bushing inside of the forward clutch hub during installation.


45. INSTALL OVERDRIVE BRAKE GASKET

  1. D003573
    Install 2 new overdrive brake gaskets.


46. INSTALL DIFFERENTIAL GEAR ASSEMBLY

  1. D026450E11
    Install the differential gear assembly to the transaxle case.


47. INSTALL NO. 2 THRUST BEARING UNDERDRIVE RACE

  1. D101208E01
    Install the No. 2 thrust bearing underdrive race to the underdrive planetary gear assembly.


48. INSTALL THRUST NEEDLE ROLLER BEARING

  1. C141527E01
    Coat the thrust needle roller bearing with ATF.

  1. Calculate the end play using the following formula and values of dimension E and F that are measured when installing the cylindrical roller bearing and underdrive planetary gear. Select an appropriate No. 2 underdrive planetary gear thrust bearing race which satisfies the specified end play, and install the selected bearing race.

    End play:
    0.498 to 0.993 mm (0.01961 to 0.03909 in.)

    HINT:
    End play = Dimension F - Dimension E - thrust bearing thickness 2.5 mm (0.0984 in.) - No. 2 underdrive thrust bearing race thickness.

    Race thickness: mm (in.) 
    F - E
    Thickness
    Less than 7.72 (0.3039)
    3.5 (0.138)
    7.72 (0.3039)
    3.8 (0.150)
    Bearing and bearing race diameter: mm (in.) 

    Inside
    Outside
    Bearing
    57.2 (2.252)
    84.96 (3.345)
    Bearing race
    56.4 (2.22)
    83 (3.268)


49. INSTALL OIL PUMP ASSEMBLY

  1. D003569E03
    Install the oil pump to the transaxle case with the 7 bolts.

    Torque:
    22 N*m{ 226 kgf*cm , 16 ft.*lbf }

  1. D003629E05
    Coat the O-ring of the oil pump with ATF.

    NOTICE:
    Confirm that the input shaft rotates smoothly with the manual operation after installing the oil pump.


50. INSTALL TRANSAXLE HOUSING

  1. D003630E14
    Remove any packing material and be careful not to spill oil on the contact surface of the transaxle case or transaxle housing.

  1. Apply seal packing to the transaxle case.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    Seal Bead Width:
    1.2 mm (0.047 in.)

  1. D003568E04
    Install the transaxle housing and 16 bolts to the transaxle case.

    Torque:
    Bolt A:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    Bolt B:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }
    Bolt C:
    29 N*m{ 295 kgf*cm , 21 ft.*lbf }
    Bolt D:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    HINT:
    Apply adhesive to bolts A and D.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
    Bolt length:
    Bolt A, B:
    50 mm (1.969 in.)
    Bolt C:
    42 mm (1.654 in.)
    Bolt D:
    72 mm (2.835 in.)

    NOTICE:
    Apply adhesive to the bolts and tighten them within 10 minutes of application.

    HINT:
    Bolt A is a non-reusable bolt. However, bolt A can be used after cleaning it.


51. INSPECT INPUT SHAFT END PLAY

  1. D008091E01
    Using a dial indicator, measure the input shaft end play.

    End play:
    0.262 to 1.249 mm (0.0103 to 0.0492 in.)


52. SUPPORT AUTOMATIC TRANSAXLE ASSEMBLY

  1. D003631
    Support the transaxle assembly on wooden blocks.


53. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

  1. D026468E01
    Coat a new oil seal with MP grease.

  1. Install the oil seal to the transaxle case.

    SST
    09950-60010   (09951-00230)
    09950-70010   (09951-07100)

    Oil seal installation depth:
    0.5 to -0.5 mm (0.02 to -0.02 in.)


54. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

  1. D026382E01
    Install the parking lock rod to the manual valve lever.


55. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

  1. D003565E01
    Install a new spacer and manual valve lever shaft to the transaxle case.

    NOTICE:
    Do not damage the oil seal when installing the shaft to the transaxle case.

  1. D003564
    Using a pin punch and hammer, drive in a new pin.

  1. D026765
    Turn the spacer and the lever shaft to align the small hole for locating the staking position in the spacer with the staking position mark on the lever shaft.

  1. Using a pin punch, stake the spacer through the small hole.

  1. Check that the spacer does not turn.


56. INSTALL MANUAL VALVE LEVER SHAFT RETAINER SPRING

  1. D003559
    Using needle-nose pliers, install the retainer spring.

    NOTICE:
    Hang the spring on the shaft firmly.


57. INSTALL PARKING LOCK PAWL BRACKET

  1. D003561E01
    Install the parking lock pawl bracket with the 2 bolts.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }

    Bolt length:
    25 mm (0.984 in.)

    NOTICE:
    Make sure that the parking rod is placed between the parking pawl and the guide of the parking bracket when the parking bracket is installed.


58. INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

  1. D003560E01
    Install the manual detent spring sub-assembly with the 2 bolts.

    NOTICE:
    Make sure to install the manual detent spring and cover in this order.

    HINT:
    Tighten bolt A first, and then bolt B.

    Torque:
    Bolt A:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }
    Bolt B:
    12 N*m{ 120 kgf*cm , 9 ft.*lbf }

    Bolt length:
    Bolt A:
    27 mm (1.063 in.)
    Bolt B:
    16 mm (0.630 in.)


59. INSTALL B-3 ACCUMULATOR PISTON

  1. D003904E10
    Coat a new O-ring with ATF and install it to the B-3 accumulator piston.

    NOTICE:
    Make sure that the O-ring is not twisted and that it does not protrude abnormally from the accumulator piston. Apply sufficient ATF before installing the O-ring. The O-ring must be installed in the correct position.

  1. D025512E01
    Coat the piston with ATF and install it to the transaxle case.

    NOTICE:
    Install the springs to each accumulator piston, checking the identification color or each spring.

    Accumulator spring: 
    Free length
    Outer diameter mm (in.)
    Color
    Inner 62.00 (2.4409) /
    15.50 (0.610)
    Purple
    Outer 74.23 (2.9224) /
    21.70 (0.854)
    Purple


60. INSTALL REVERSE CLUTCH ACCUMULATOR PISTON

  1. D026402E08
    Coat 2 new O-rings with ATF and install them to the reverse accumulator piston.

    NOTICE:
    Make sure that the O-ring is not twisted and that it does not protrude abnormally from the accumulator piston. Apply sufficient ATF before installing the O-ring. The O-ring must be installed in the correct position.

  1. C092978E02
    Coat the piston with ATF and install it to the transaxle case.

    NOTICE:
    Install the springs to each accumulator piston, checking the identification color or each spring.

    Accumulator spring: 
    Free length
    Outer diameter mm (in.)
    Color
    60.96 (2.3999) /
    14.10 (0.555)
    Yellow


61. INSTALL C-3 ACCUMULATOR PISTON

  1. D003902E04
    Coat a new O-ring with ATF and install it to the C-3 accumulator piston.

    NOTICE:
    Make sure that the O-ring is not twisted and that it does not protrude abnormally from the accumulator piston. Apply sufficient ATF before installing the O-ring. The O-ring must be installed in the correct position.

  1. C083146
    Coat the piston with ATF and install it to the transaxle case.

    NOTICE:
    Install the springs to each accumulator piston, checking the identification color or each spring.

    Accumulator spring: 
    Free length
    Outer diameter mm (in.)
    Color
    72.20 (2.8425) /
    19.0 (0.748)
    Colorless

  1. D003555
    Install the spring to the C-3 accumulator piston.

    NOTICE:
    Install the springs to each accumulator piston, checking the identification color or each spring.


62. INSTALL CHECK BALL BODY

  1. D003554E01
    Coat the check ball body with ATF.

  1. Install the check ball body and spring.

    NOTICE:
    Be sure to place the spring in the hole in the check ball body. Make sure that they are installed in the correct direction.


63. INSTALL BRAKE DRUM GASKET

  1. C083129
    Coat a new brake drum gasket with ATF and install it to the transaxle case.

    NOTICE:
    Be sure not to damage the lip of the transaxle case brake gasket when inserting the gasket to the case. Apply sufficient ATF to the gasket before installation. Make sure that they are installed in the correct direction.


64. INSTALL TRANSAXLE CASE 2ND BRAKE GASKET

  1. C083128
    Coat a new transaxle case 2nd brake gasket with ATF and install it to the transaxle case.

    NOTICE:
    Be sure not to damage the lip of the transaxle case brake gasket when inserting the gasket to the case. Apply sufficient ATF to the gasket before installation. Make sure that they are installed in the correct direction.


65. INSTALL NO. 1 GOVERNOR APPLY GASKET

  1. C083127
    Coat a new No. 1 governor apply gasket with ATF and install it to the transaxle case.

    NOTICE:
    Be sure not to damage the lip of the transaxle case brake gasket when inserting the gasket to the case. Apply sufficient ATF to the gasket before installation. Make sure that they are installed in the correct direction.


66. INSTALL TRANSMISSION WIRE

  1. D003636E01
    Coat a new O-ring with ATF and install it to the transmission wire.

    NOTICE:
    Make sure that the O-ring is not twisted, protruded, or pinched when installing the wire transmission to the transaxle case. Apply sufficient ATF to the O-ring before installation.

  1. D003547E10
    Install the bolt that retains the transmission wire.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


67. CONNECT TRANSMISSION WIRE

  1. C091927E05
    Coat an O-ring of the ATF temperature sensor with ATF.

  1. Install the ATF temperature sensor with the lock plate and bolt.

    Torque:
    6.6 N*m{ 67 kgf*cm , 58 in.*lbf }

  1. Connect the 7 solenoid connectors.

    NOTICE:
    1. Connect the connectors A, B, C, D, E, F, G, in the order from the shortest to longest.
    2. Apply ATF to the bolt.


68. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

  1. C091933E02
    While positioning the manual valve lever position, install the valve body to the transaxle case with the 17 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    Bolt length:
    Bolt A:
    25 mm (0.984 in.)
    Bolt B:
    57 mm (2.244 in.)
    Bolt C:
    41 mm (1.614 in.)

    NOTICE:
    1. Push the valve body against the accumulator piston spring and the check ball body to install the valve body.
    2. When installing the valve body to the transaxle case, do not hold the solenoids.
    3. Temporarily tighten the bolts marked (1) in the illustration first because they are positioning bolts.


69. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

  1. C091932E03
    Coat a new O-ring with ATF and install it to the oil strainer.

    NOTICE:
    Make sure that the O-ring is not twisted or pinched. Apply sufficient ATF to the O-ring before installation.

  1. C091931
    Install the oil strainer and 3 bolts to the valve body.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    NOTICE:
    Apply ATF to the bolts.


70. INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

  1. D030865E03
    Install the 2 magnets to the oil pan.

  1. Apply adhesive to 18 new bolts.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  1. C091925
    Install the oil pan and new oil pan gasket to the transaxle case with the 18 bolts.

    Torque:
    7.8 N*m{ 80 kgf*cm , 69 in.*lbf }

    NOTICE:
    1. Apply adhesive to the bolts and tighten them within 10 minutes of application.
    2. Completely remove any oil or grease from the contact surface of the transaxle case and the oil pan with the gasket before installing the oil pan to the case.


71. INSTALL NO. 1 TRANSAXLE CASE PLUG

  1. D026716
    Coat 4 new O-rings with ATF, and install them to the 4 No. 1 transaxle case plugs.

  1. Install the 4 No. 1 transaxle case plugs to the transaxle case.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


72. INSTALL SPEED SENSOR

  1. C161143E01
    Coat 2 new O-rings with ATF and install them to the 2 sensors.

  1. Install the 2 sensors to the transaxle case with the 2 bolts.

    Torque:
    11 N*m{ 115 kgf*cm , 8 ft.*lbf }


73. INSTALL OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)

  1. C083144E05
    Coat a new O-ring with ATF and install it to the elbow.

  1. Install the elbow to the transaxle case.

    Torque:
    27 N*m{ 276 kgf*cm , 20 ft.*lbf }


74. INSTALL OIL COOLER TUBE UNION (INLET OIL COOLER UNION)

  1. C083143E04
    Coat a new O-ring with ATF and install it to the union.

  1. Install the union to the transaxle case.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }


75. INSTALL BREATHER PLUG HOSE
  1. Install the breather plug hose to the transaxle case firmly.


76. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

  1. C099454
    Install the park/neutral position switch to the manual valve shaft.

  1. Temporarily install the 2 bolts.

  1. G025453
    Place a new lock plate and tighten the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. Temporarily install the control shaft lever.

  1. C099455
    Turn the lever counterclockwise until it stops, and then turn it clockwise 2 notches.

  1. Remove the control shaft lever.

  1. C099456E04
    Align the groove with the neutral basic line.

  1. Hold the switch position and tighten the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C161138
    Using a screwdriver, bend the tabs of the lock plate.

  1. C099458
    Install the control shaft lever, washer and nut.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }


77. INSTALL SPEEDOMETER DRIVEN HOLE (ATM) COVER SUB-ASSEMBLY
  1. Coat a new O-ring with ATF and install it to the speedometer driven hole cover.

  1. Install the bolt and speedometer driven hole cover sub-assembly to the transaxle assembly.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

← INSPECTION (from May 2007)COMPONENTS (from May 2007) →