2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Headlight Relay Circuit

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

  1. The main body receives the light control switch HEAD signal to control the headlight relays. The headlight relays are installed in the power distributor (engine room junction block assembly).
  2. When the light control switch is in AUTO position, the main body ECU receives the ambient light level signal from the automatic light control sensor to control the headlight relays.

WIRING DIAGRAM

E142681E03

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Select the following menu items: Body Electrical / Main Body / Active Test.

  1. Check that the relays operate.

    Main Body: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Headlight Relay
    Headlight Relay
    ON/OFF
    -

    OK:
    Headlight relays operate. (LO-beam headlights illuminate.)



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY

  1. E121533E02
    Remove the H-LP (LL) fuse and H-LP (RL) fuse from the engine room junction block assembly.

  1. Measure the voltage between the loading slot of each fuse and body ground.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    H-LP (LL) fuse terminal - Body ground
    Light control switch OFF → HEAD
    Below 1 V → 11 to 14 V
    H-LP (RL) fuse terminal - Body ground
    Light control switch OFF → HEAD
    Below 1 V → 11 to 14 V



NG
Go to step 3
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUSE - BODY GROUND)

3. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY

  1. A137364E14
    Remove the engine room junction block assembly from the engine room relay block.

  1. Connect the positive (+) lead from the battery to terminal 2G-1

  1. Connect the negative (-) lead from the battery to terminal 2D-8 and 2D-9.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    2B-4 - Battery negative
    Always
    11 to 14 V
    2B-5 - Battery negative
    Always
    11 to 14 V



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY
OK


4. CHECK HARNESS AND CONNECTOR (BATTERY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)

  1. E151692E01
    Disconnect the 2G engine room junction block assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connector
    Condition
    Specified Condition
    2G-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - MAIN BODY ECU)

  1. E151657E01
    Disconnect the 2D engine room junction block assembly connector.

  1. Disconnect the 1D instrument panel junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-9 - 1D-3
    Always
    Below 1 Ω
    2D-9 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - BODY GROUND)

  1. E151658E01
    Disconnect the 2D engine room junction block assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-8 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← Headlight Relay Circuit (May 2007 – Jul 2008)Headlight Relay Circuit (from Jul 2010) →