Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM
Headlight Relay Circuit
Circuit diagnosis · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The main body receives the light control switch HEAD signal to control the headlight relays. The headlight relays are installed in the power distributor (engine room junction block assembly).
When the light control switch is in AUTO position, the main body ECU receives the ambient light level signal from the automatic light control sensor to control the headlight relays.
WIRING DIAGRAM
INSPECTION PROCEDURE
1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Select the following menu items: Body Electrical / Main Body / Active Test.
Check that the relays operate.
Main Body:
Tester Display
Test Part
Control Range
Diagnostic Note
Headlight Relay
Headlight Relay
ON/OFF
-
OK:
Headlight relays operate. (LO-beam headlights illuminate.)
NG
OK
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here )
2. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY
Remove the H-LP LH LO fuse and H-LP RH LO fuse from the engine room junction block assembly.
Measure the voltage between the loading slot of each fuse and body ground.
Standard voltage:
Tester Connection
Switch Condition
Specified Condition
H-LP LH LO fuse terminal - Body ground
Light control switch OFF → HEAD
Below 1 V → 11 to 14 V
H-LP RH LO fuse terminal - Body ground
Light control switch OFF → HEAD
Below 1 V → 11 to 14 V
NG
OK
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUSE - BODY GROUND)
3. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY
Remove the engine room junction block assembly from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connection
Condition
Specified Condition
2B-4 - Battery negative (-)
Battery positive (+) - 2G-1 Battery negative (-) - 2D-9 Battery negative (-) - 2E-11
11 to 14 V
2B-5 - Battery negative (-)
11 to 14 V
NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY
OK
4. CHECK HARNESS AND CONNECTOR (BATTERY - ENGINE ROOM JUNCTION BLOCK ASSEMBLY)
Disconnect the 2G engine room junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
Standard voltage:
Tester Connector
Condition
Specified Condition
2G-1 - Body ground
Always
11 to 14 V
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
5. CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - MAIN BODY ECU)
Disconnect the 2D engine room junction block assembly connector.
Disconnect the 1D instrument panel junction block connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
2D-9 - 1D-3
Always
Below 1 Ω
2D-9 - Body ground
Always
10 kΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
6. CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - BODY GROUND)
Disconnect the 2E engine room junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
Standard resistance:
Tester Connection
Condition
Specified Condition
2E-11 - Body ground
Always
Below 1 Ω
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)