2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Key Reminder Buzzer does not Sound

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is in the LOCK or ACC positions. The key reminder warning buzzer is activated when the main body ECU sends a key switch signal and driver side courtesy switch signal to the combination meter.

HINT:
Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "HOW TO PROCEED WITH TROUBLESHOOTING" procedures. Then, conduct the following inspection procedure.


WIRING DIAGRAM

B172183E04

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (FRONT DOOR COURTESY LIGHT SWITCH)
  1. Check the Data List for proper functioning of the driver side door courtesy light switch.

    MAIN BODY 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door Courtesy SW
    Front door courtesy light switch signal / ON or OFF
    ON: Driver side door is open
    OFF: Driver side door is closed
    -

    OK:
    ON (driver door is open) appears on the screen.



NG
Go to step 5
OK


2. READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH)
  1. Check the Data List for proper functioning of the unlock warning switch.

    MAIN BODY 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Unlock Warning SW
    Unlock warning switch signal / ON or OFF
    ON: Key is in ignition key cylinder
    OFF: No key is in ignition key cylinder
    -

    OK:
    ON (Key is in ignition key cylinder) appears on the screen.



NG
Go to step 3
OK

REPLACE COMBINATION METER ASSEMBLY

3. INSPECT UNLOCK WARNING SWITCH ASSEMBLY

  1. B159681E05
    Remove the unlock warning switch assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch free (Key removed)
    10 kΩ or higher
    1 - 2
    Switch pushed (Key set)
    Below 1 Ω



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU)

  1. B175265E03
    Disconnect the D16 unlock warning switch assembly and D9 ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D16-1 - D9-5 (KSW)
    Always
    Below 1 Ω
    D16-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)

5. INSPECT FRONT DOOR COURTESY LIGHT SWITCH (for Driver Side)

  1. B111600E12
    Remove the driver's side front door courtesy light switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - Switch body
    Courtesy switch pushed (Door closed)
    10 kΩ or higher
    Courtesy switch free (Door open)
    Below 1 Ω



NG
REPLACE FRONT DOOR COURTESY LIGHT SWITCH (for Driver Side) (Click here)
OK


6. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH - MAIN BODY ECU)

  1. B176394E01
    Disconnect the D7 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    O2-1 - D7-24 (DCTY)
    Always
    Below 1 Ω
    O2-1 - Body ground
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    N2-1 - D7-24 (DCTY)
    Always
    Below 1 Ω
    N2-1 - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK (MAIN BODY ECU)


← Key Reminder Buzzer does not Sound (May 2007 – Jul 2008)Key Reminder Buzzer does not Sound (from Jul 2010) →