Key Reminder Buzzer does not Sound
Circuit diagnosis · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is in the LOCK or ACC positions. The key reminder warning buzzer is activated when the main body ECU sends a key switch signal and driver side courtesy switch signal to the combination meter.- HINT:
- Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting the CAN communication functions in accordance with the "HOW TO PROCEED WITH TROUBLESHOOTING" procedures. Then, conduct the following inspection procedure.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (FRONT DOOR COURTESY LIGHT SWITCH) |
Check the Data List for proper functioning of the driver side door courtesy light switch.
MAIN BODY Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door Courtesy SW
Front door courtesy light switch signal / ON or OFF
ON: Driver side door is open
OFF: Driver side door is closed
-
- OK:
- ON (driver door is open) appears on the screen.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH) |
Check the Data List for proper functioning of the unlock warning switch.
MAIN BODY Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Key Unlock Warning SW
Unlock warning switch signal / ON or OFF
ON: Key is in ignition key cylinder
OFF: No key is in ignition key cylinder
-
- OK:
- ON (Key is in ignition key cylinder) appears on the screen.
|
|
||||
| OK | ||
| ||
| 3. INSPECT UNLOCK WARNING SWITCH ASSEMBLY |
Remove the unlock warning switch assembly (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Switch free (Key removed)
10 kΩ or higher
1 - 2
Switch pushed (Key set)
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH - MAIN BODY ECU) |
Disconnect the D16 unlock warning switch assembly and D9 ECU connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D16-1 - D9-5 (KSW)
Always
Below 1 Ω
D16-1 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 5. INSPECT FRONT DOOR COURTESY LIGHT SWITCH (for Driver Side) |
Remove the driver's side front door courtesy light switch (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
1 - Switch body
Courtesy switch pushed (Door closed)
10 kΩ or higher
Courtesy switch free (Door open)
Below 1 Ω
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH - MAIN BODY ECU) |
Disconnect the D7 ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
for LHD Tester Connection
Condition
Specified Condition
O2-1 - D7-24 (DCTY)
Always
Below 1 Ω
O2-1 - Body ground
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
N2-1 - D7-24 (DCTY)
Always
Below 1 Ω
N2-1 - Body ground
10 kΩ or higher
|
|
||||
| OK | ||
| ||
