2007-2013 Highlander Kluger · Service Manual BODY

Rear Power Window RH does not Operate with Rear Power Window Switch RH

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

If the rear RH side manual UP/DOWN function does not operate, a malfunction may exist in the power window regulator motor, power window switch, power window master switch or wire harness.

WIRING DIAGRAM

B177581E02

INSPECTION PROCEDURE


1. CHECK POWER WINDOW SWITCH (REAR RH) (POWER SOURCE)

  1. B175982E04
    Disconnect the J2 connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    J2-3 (B) - Body ground
    Ignition switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT POWER WINDOW SWITCH (REAR RH)

  1. B164433E07
    Measure the resistance when the switch is operated according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (D) - 2 (SD)
    UP
    Below 1 Ω
    3 (B) - 4 (U)
    Below 1 Ω
    1 (D) - 2 (SD)
    OFF
    Below 1 Ω
    4 (U) - 5 (SU)
    Below 1 Ω
    4 (U) - 5 (SU)
    DOWN
    Below 1 Ω
    1 (D) - 3 (B)
    Below 1 Ω



NG
REPLACE POWER WINDOW SWITCH (REAR RH) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (SWITCH (REAR RH) - MOTOR (REAR RH))

  1. B175983E06
    Disconnect the J2 and J3 connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J2-4 (U) - J3-1 (U)
    Always
    Below 1 Ω
    J2-1 (D) - J3-2 (D)
    Always
    Below 1 Ω
    J2-4 (U) - Body ground
    Always
    10 kΩ or higher
    J2-1 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH)

  1. Check power window regulator motor operation.

    1. B164427E04
      Remove the power window regulator motor (Click here).

    2. Apply battery voltage to the motor connector according to the table below.

      NOTICE:
      Do not apply battery voltage to any terminals except terminals 1 and 2.

      OK:
      Measurement Condition
      Specified Condition
      Battery negative (-) → Terminal 1
      Battery positive (+) → Terminal 2
      Motor gear rotates clockwise
      Battery negative (-) → Terminal 2
      Battery positive (+) → Terminal 1
      Motor gear rotates counterclockwise

  1. Check PTC operation.

    NOTICE:
    The work must be performed with the power window regulator and door glass installed on the vehicle.

    1. Install the power window regulator motor (Click here).

    2. B164428E16
      Connect an electrical tester DC 400 A probe to the wire harness of terminal 1.

      NOTICE:
      Match the arrow mark of the probe with the direction of the current flow.

    3. Fully close the door glass by pressing the power window UP switch. Wait for approximately 60 seconds.

    4. Continue to press the power window UP switch and measure how long it takes for the electrical current to change from a range of 16 to 28 A to approximately 1 A (Inspection of current shut-off).

      Standard:
      4 to 90 seconds

    5. 60 seconds after the previous step, press the power window DOWN switch (rear RH side).

      OK:
      The rear RH side window goes down.



NG
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH) (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - SWITCH (REAR RH))

  1. B175975E03
    for LHD:
    1. for Rear RH side:Disconnect the M1 and J2 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-10 (U) - J2-5 (SU)
      Always
      Below 1 Ω
      M1-18 (D) - J2-2 (SD)
      Always
      Below 1 Ω
      M1-10 (U) - Body ground
      Always
      10 kΩ or higher
      M1-18 (D) - Body ground
      Always
      10 kΩ or higher

  1. B175975E10
    for RHD:
    1. for Rear RH side:Disconnect the L1 and J2 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-16 (U) - J2-5 (SU)
      Always
      Below 1 Ω
      L1-15 (D) - J2-2 (SD)
      Always
      Below 1 Ω
      L1-16 (U) - Body ground
      Always
      10 kΩ or higher
      L1-15 (D) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW MASTER SWITCH (Click here)


← Rear Power Window RH does not Operate with Rear Power Window Switch RH (Aug 2008 – Jun 2010)Driver Side Power Window Auto Up / Down Function does not Operate with Power Window Master Switch (May 2007 – Jul 2008) →