2007-2013 Highlander Kluger · Service Manual BODY

Remote Up / Down Function does not Operate

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

With the ignition switch ON, the power window regulator master switch transmits remote switch signals to the regulator switch of the passenger door power window. Then, the regulator switch drives the passenger power window regulator motor.

WIRING DIAGRAM

B175978E05
B175978E06

INSPECTION PROCEDURE


1. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

  1. B141161
    Turn the window lock switch OFF and operate the switches on the master switch. Check that the remote UP / DOWN function operates normally.

    OK:
    Remote UP / DOWN function operates normally.



NG
Go to step 2
OK

END

2. CHECK MANUAL UP / DOWN FUNCTION
  1. Check that the passenger door power window manual UP / DOWN function operates normally.

    OK:
    Manual UP / DOWN function operates normally.



NG
Go to step 3
OK

REPLACE POWER WINDOW MASTER SWITCH (Click here)

3. HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - BATTERY AND BODY GROUND)

  1. for LHD:

    1. B175979E01
      Disconnect the M1 connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      M1-6 (B) - Body ground
      Ignition switch on (IG)
      11 to 14 V

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-1 (E) - Body ground
      Always
      Below 1 Ω

  1. for RHD:

    1. B175979E02
      Disconnect the L1 connector.

    2. Measure the voltage and resistance according to the value(s) in the table below.

      Standard voltage:
      Tester Connection
      Condition
      Specified Condition
      L1-6 (B) - Body ground
      Ignition switch on (IG)
      11 to 14 V

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-9 (E) - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT POWER WINDOW MASTER SWITCH

  1. B164359E14
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    6 (B) - 16 (U)
    15 (D) - 1 (E)
    UP (Passenger side)
    Below 1 Ω
    6 (B) - 15 (D)
    16 (U) - 1 (E)
    DOWN (Passenger side)
    Below 1 Ω
    6 (B) - 12 (U)
    13 (D) - 1 (E)
    UP (Rear LH)
    Below 1 Ω
    6 (B) - 13 (D)
    12 (U) - 1 (E)
    DOWN (Rear LH)
    Below 1 Ω
    6 (B) - 10 (U)
    18 (D) - 1 (E)
    UP (Rear RH)
    Below 1 Ω
    6 (B) - 18 (D)
    10 (U) - 1 (E)
    DOWN (Rear RH)
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    6 (B) - 12 (U)
    13 (D) - 9 (E)
    UP (Passenger side)
    Below 1 Ω
    6 (B) - 13 (D)
    12 (U) - 9 (E)
    DOWN (Passenger side)
    Below 1 Ω
    6 (B) - 18 (U)
    10 (D) - 9 (E)
    UP (Rear LH)
    Below 1 Ω
    6 (B) - 10 (D)
    18 (U) - 9 (E)
    DOWN (Rear LH)
    Below 1 Ω
    6 (B) - 16 (U)
    15 (D) - 9 (E)
    UP (Rear RH)
    Below 1 Ω
    6 (B) - 15 (D)
    16 (U) - 9 (E)
    DOWN (Rear RH)
    Below 1 Ω



NG
REPLACE POWER WINDOW MASTER SWITCH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - FRONT PASSENGER, REAR LH/RH SWITCH)

  1. B175975E01
    for LHD:
    1. Front passenger side:Disconnect the M1 and G7 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-16 (U) - G7-5 (SU)
      Always
      Below 1 Ω
      M1-15 (D) - G7-2 (SD)
      Always
      Below 1 Ω
      M1-16 (U) - Body ground
      Always
      10 kΩ or higher
      M1-15 (D) - Body ground
      Always
      10 kΩ or higher

    3. B175975E02
      for Rear LH side:Disconnect the M1 and K2 connectors.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-12 (U) - K2-5 (SU)
      Always
      Below 1 Ω
      M1-13 (D) - K2-2 (SD)
      Always
      Below 1 Ω
      M1-12 (U) - Body ground
      Always
      10 kΩ or higher
      M1-13 (D) - Body ground
      Always
      10 kΩ or higher

    5. B175975E03
      for Rear RH side:Disconnect the M1 and J2 connectors.

    6. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M1-10 (U) - J2-5 (SU)
      Always
      Below 1 Ω
      M1-18 (D) - J2-2 (SD)
      Always
      Below 1 Ω
      M1-10 (U) - Body ground
      Always
      10 kΩ or higher
      M1-18 (D) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. B175975E04
      Front passenger side:Disconnect the L1 and H10 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-12 (U) - H10-5 (SU)
      Always
      Below 1 Ω
      L1-13 (D) - H10-2 (SD)
      Always
      Below 1 Ω
      L1-12 (U) - Body ground
      Always
      10 kΩ or higher
      L1-13 (D) - Body ground
      Always
      10 kΩ or higher

    3. B175975E05
      for Rear LH side:Disconnect the L1 and K2 connectors.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-18 (U) - K2-5 (SU)
      Always
      Below 1 Ω
      L1-10 (D) - K2-2 (SD)
      Always
      Below 1 Ω
      L1-18 (U) - Body ground
      Always
      10 kΩ or higher
      L1-10 (D) - Body ground
      Always
      10 kΩ or higher

    5. B175975E06
      for Rear RH side:Disconnect the L1 and J2 connectors.

    6. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      L1-16 (U) - J2-5 (SU)
      Always
      Below 1 Ω
      L1-15 (D) - J2-2 (SD)
      Always
      Below 1 Ω
      L1-16 (U) - Body ground
      Always
      10 kΩ or higher
      L1-15 (D) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW SWITCH (APPLICABLE LOCATION)


← Remote Up / Down Function does not Operate (Aug 2008 – Jun 2010)Driver Side Power Window does not Operate with Power Window Master Switch (May 2007 – Jul 2008) →