Remote Up / Down Function does not Operate
Circuit diagnosis · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
With the ignition switch ON, the power window regulator master switch transmits remote switch signals to the regulator switch of the passenger door power window. Then, the regulator switch drives the passenger power window regulator motor.WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY |
Turn the window lock switch OFF and operate the switches on the master switch. Check that the remote UP / DOWN function operates normally.

- OK:
- Remote UP / DOWN function operates normally.
|
|
||||
| OK | ||
| ||
| 2. CHECK MANUAL UP / DOWN FUNCTION |
Check that the passenger door power window manual UP / DOWN function operates normally.
- OK:
- Manual UP / DOWN function operates normally.
|
|
||||
| OK | ||
| ||
| 3. HARNESS AND CONNECTOR (POWER WINDOW MASTER SWITCH - BATTERY AND BODY GROUND) |
for LHD:
Disconnect the M1 connector.

Measure the voltage and resistance according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
M1-6 (B) - Body ground
Ignition switch on (IG)
11 to 14 V
- Standard resistance:
Tester Connection
Condition
Specified Condition
M1-1 (E) - Body ground
Always
Below 1 Ω
for RHD:
Disconnect the L1 connector.

Measure the voltage and resistance according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
L1-6 (B) - Body ground
Ignition switch on (IG)
11 to 14 V
- Standard resistance:
Tester Connection
Condition
Specified Condition
L1-9 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. INSPECT POWER WINDOW MASTER SWITCH |
Measure the resistance according to the value(s) in the table below.

- Standard resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
6 (B) - 16 (U)
15 (D) - 1 (E)
UP (Passenger side)
Below 1 Ω
6 (B) - 15 (D)
16 (U) - 1 (E)
DOWN (Passenger side)
Below 1 Ω
6 (B) - 12 (U)
13 (D) - 1 (E)
UP (Rear LH)
Below 1 Ω
6 (B) - 13 (D)
12 (U) - 1 (E)
DOWN (Rear LH)
Below 1 Ω
6 (B) - 10 (U)
18 (D) - 1 (E)
UP (Rear RH)
Below 1 Ω
6 (B) - 18 (D)
10 (U) - 1 (E)
DOWN (Rear RH)
Below 1 Ω
- for RHD:
Tester Connection
Condition
Specified Condition
6 (B) - 12 (U)
13 (D) - 9 (E)
UP (Passenger side)
Below 1 Ω
6 (B) - 13 (D)
12 (U) - 9 (E)
DOWN (Passenger side)
Below 1 Ω
6 (B) - 18 (U)
10 (D) - 9 (E)
UP (Rear LH)
Below 1 Ω
6 (B) - 10 (D)
18 (U) - 9 (E)
DOWN (Rear LH)
Below 1 Ω
6 (B) - 16 (U)
15 (D) - 9 (E)
UP (Rear RH)
Below 1 Ω
6 (B) - 15 (D)
16 (U) - 9 (E)
DOWN (Rear RH)
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (MASTER SWITCH - FRONT PASSENGER, REAR LH/RH SWITCH) |
for LHD:

Front passenger side:Disconnect the M1 and G7 connectors.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
M1-16 (U) - G7-5 (SU)
Always
Below 1 Ω
M1-15 (D) - G7-2 (SD)
Always
Below 1 Ω
M1-16 (U) - Body ground
Always
10 kΩ or higher
M1-15 (D) - Body ground
Always
10 kΩ or higher
for Rear LH side:Disconnect the M1 and K2 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
M1-12 (U) - K2-5 (SU)
Always
Below 1 Ω
M1-13 (D) - K2-2 (SD)
Always
Below 1 Ω
M1-12 (U) - Body ground
Always
10 kΩ or higher
M1-13 (D) - Body ground
Always
10 kΩ or higher
for Rear RH side:Disconnect the M1 and J2 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
M1-10 (U) - J2-5 (SU)
Always
Below 1 Ω
M1-18 (D) - J2-2 (SD)
Always
Below 1 Ω
M1-10 (U) - Body ground
Always
10 kΩ or higher
M1-18 (D) - Body ground
Always
10 kΩ or higher
for RHD:
Front passenger side:Disconnect the L1 and H10 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
L1-12 (U) - H10-5 (SU)
Always
Below 1 Ω
L1-13 (D) - H10-2 (SD)
Always
Below 1 Ω
L1-12 (U) - Body ground
Always
10 kΩ or higher
L1-13 (D) - Body ground
Always
10 kΩ or higher
for Rear LH side:Disconnect the L1 and K2 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
L1-18 (U) - K2-5 (SU)
Always
Below 1 Ω
L1-10 (D) - K2-2 (SD)
Always
Below 1 Ω
L1-18 (U) - Body ground
Always
10 kΩ or higher
L1-10 (D) - Body ground
Always
10 kΩ or higher
for Rear RH side:Disconnect the L1 and J2 connectors.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
L1-16 (U) - J2-5 (SU)
Always
Below 1 Ω
L1-15 (D) - J2-2 (SD)
Always
Below 1 Ω
L1-16 (U) - Body ground
Always
10 kΩ or higher
L1-15 (D) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
