2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built from Jul 2010


NAVIGATION RECEIVER ASSEMBLY OUTLINE

  1. Conventionally, 2 separate devices, a "radio and display" and a "navigation ECU" are used. This model has adopted a type that combines these devices into a single unit. The hard disk drive which contains map and other data is built into the navigation ECU.
    E187103E01


NAVIGATION SYSTEM OUTLINE

  1. Vehicle position tracking methods
    It is essential that the navigation system correctly tracks the current vehicle position and displays it on the map. There are 2 methods to track the current vehicle position: autonomous (dead reckoning) and GPS* (satellite) navigation. Both navigation methods are used in conjunction with each other.
    *GPS (Global Positioning System)
    E187279E01

    Operation
    Description
    Vehicle Position Calculation
    The navigation receiver assembly calculates the current vehicle position (direction and current position) using the direction deviation signal from the gyro sensor and driving distance signal from the vehicle speed sensor and creates the driving route.
    Map Display Processing
    The navigation receiver assembly processes the vehicle position data, vehicle driving track and map data from the hard disk drive.
    Map Matching
    The map data from the hard disk drive is compared to the vehicle position and driving track data. Then, the vehicle position is matched with the nearest road.
    GPS Correction
    The vehicle position is matched to the position measured by GPS. Then, the GPS measurement position data is compared with the vehicle position and driving track data. If the position is very different, the GPS measurement position is used.
    Distance Correction
    The vehicle speed signal includes the error caused by tire wear and slippage between the tires and road surface. Distance correction is performed to account for this. The navigation receiver assembly automatically offsets the signal to make up for the difference between it and the distance data of the map. The offset is automatically updated.
    I100028E41

    HINT:
    The combination of autonomous and GPS navigation makes it possible to display the vehicle position even when the vehicle is in places where GPS signals cannot be received. When only autonomous navigation is used, however, the mapping accuracy may slightly decrease.

  2. Autonomous navigation
    This method determines the relative vehicle position based on the driving track determined by the gyro located in the navigation receiver assembly and the vehicle speed signal.

    1. Gyro sensor
      Used to calculate the direction by detecting angular velocity. It is located in the navigation receiver assembly.

    2. Vehicle speed signal
      Used to calculate the vehicle driving distance.

  3. GPS* navigation (Satellite navigation)
    This method detects the absolute vehicle position using radio waves from GPS satellites.
    *: GPS satellites were launched by the U.S. Department of Defense for military purposes.
    I100029E07

    Number of Satellites
    Measurement
    Description
    2 or less
    Measurement is impossible
    Vehicle position cannot be obtained because the number of satellites is not enough.
    3
    2-dimensional measurement is possible
    Vehicle position is obtained based on the current longitude and latitude. (This is less precise than 3-dimensional measurement.)
    4
    3-dimensional measurement is possible
    Vehicle position is obtained based on the current longitude, latitude and altitude.

  4. Map matching
    The current driving route is calculated by autonomous navigation (according to the gyro sensor and vehicle speed signal) and GPS navigation. This information is then compared with possible road shapes from the map data in the hard disk drive and the vehicle position is set onto the most appropriate road.
    I100030E40

  5. Touch switch
    Touch switches are touch-sensitive (interactive) switches operated by touching the screen. When a switch is pressed, the outer glass bends in to contact the inner glass at the pressed position. By doing this, the voltage ratio is measured and the pressed position is detected.
    E106414E05


CD (COMPACT DISC) PLAYER OUTLINE
  1. A compact disc player uses a laser pickup to read digital signals recorded on a compact disc (CD). By converting the digital signals to analog, it can play music and audio.

    CAUTION:
    Do not look directly at the laser pickup because the CD player uses an invisible laser beam. Be sure to operate the player only as instructed.

    NOTICE:
    1. Do not disassemble any part of the CD player.
    2. Do not apply oil to the CD player.
    3. Do not insert anything but a CD into the CD player.

  2. Usable discs

    1. This player can play only audio CDs, CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) that have any of the following marks:
      E119759

  3. Precautions for use of discs

    NOTICE:
    1. Copy-protected CDs cannot be played.
    2. CD-Rs and CD-RWs may not be played depending on the recording conditions or characteristics of the discs, or due to damage, dirt or deterioration caused by leaving the discs in the cabin for a long time.
    3. Unfinalized CD-Rs and CD-RWs cannot be played.
    4. DualDiscs that mate DVD recorded material on one side with CD digital audio material on the other cannot be played.
    5. Keep the discs away from dirt. Be careful not to damage the discs or leave your fingerprints on them.
    6. Hold discs by the outer edge and center hole with the label side up.
    7. Leaving the disc exposed halfway out of the slot for a long time after pressing the disc eject button may cause deformation of the disc, making the disc unusable.
    8. If discs have adhesive tape, stickers, CD labels or any traces of such labels attached, the discs may not be ejected or player malfunctions may result.
    9. Keep the discs away from direct sunlight. (Exposure to direct sunlight may cause deformation of the disc, making the disc unusable.)
    10. Do not use odd-shaped CDs because these may cause player malfunctions.
    11. Do not use discs whose recording portion is transparent or translucent because they may not be inserted, ejected or played normally.

    HINT:
    1. When it is cold or it is raining, if the windows mist up, mist and condensation may form in the player. In such cases, the CD may skip or stop in the middle of play. Ventilate or dehumidify the cabin for a while before using the player.
    2. The CD may skip if the player experiences strong vibrations when the vehicle is driven on rough roads or similar uneven surfaces.

  4. I100151
    Cleaning

    NOTICE:
    Do not use a lens cleaner because it may cause a malfunction in the pickup portion of the player.


    1. If dirt is on the disc surface, wipe it clean with a soft dry cloth such as an eyeglass cleaner for plastic lenses from the inside to the outside in a radial direction.

      NOTICE:
      1. Pressing on the disc by hand or rubbing the disc with a hard cloth may scratch the disc surface.
      2. Use of solvents such as record spray, antistatic agents, alcohol, benzine, thinners or a chemical cloth may cause damage to the disc, making the disc unusable.


MP3/WMA OUTLINE
  1. Playable MP3 file standards

    Compatible standard
    MP3 (MPEG1 LAYER3, MPEG2 LSF LAYER3)
    Compatible sampling frequency
    1. MPEG1 LAYER3: 32, 44.1, 48 (kHz)
    2. MPEG2 LSF LAYER3: 16, 22.05, 24 (kHz)
    Compatible bit rate
    1. MPEG1 LAYER3: 64, 80, 96, 112, 128, 160, 192, 224, 256, 320 (kbps)
    2. MPEG2 LSF LAYER3: 64, 80, 96, 112, 128, 144, 160 (kbps)
    3. Compatible with VBR
    Compatible channel mode
    Stereo, joint stereo, dual channel, monaural

  2. Playable WMA file standards

    Compatible standard
    WMA Ver. 7, 8, and 9
    Compatible sampling frequency
    32, 44.1, 48 (kHz)
    Compatible bit rate (Only compatible with 2-channel playback)
    1. Ver. 7, 8: CBR48, 64, 80, 96, 128, 160, 192 (kbps)
    2. Ver. 9: CBR48, 64, 80, 96, 128, 160, 192, 256, 320 (kbps)

  3. ID3 tag and WMA tag

    1. Additional text information called an ID3 tag can be input to MP3 files. Information such as song titles and artist names can be stored.

      HINT:
      This player is compatible with ID3 tags of ID3 Ver. 1.0 and 1.1, and ID3 Ver. 2.2 and 2.3. (Number of characters complies with ID3 Ver. 1.0 and 1.1.)

    2. Additional text information called a WMA tag can be input to WMA files. Information such as song titles and artist names can be stored.

  4. Usable media

    1. Only CD-ROMs, CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) can be used to play MP3/WMA files.

      NOTICE:
      1. CD-Rs and CD-RWs are more easily affected by a hot and humid environment than discs used for normal audio CDs. For this reason, some CD-Rs and CD-RWs do not play.
      2. If there are fingerprints or scratches on a disc, the disc may not play or the CD may skip.
      3. Some CD-Rs and CD-RWs may deteriorate if they are left in the cabin for a long time.
      4. Keep CD-Rs and CD-RWs in an opaque case.

  5. Usable media format

    1. Usable media format

      Disc format
      CD-ROM Mode 1, CD-ROM XA Mode 2 Form 1
      File format
      ISO9660 Level 1 and Level 2 (Joliet, Romeo)

      HINT:
      1. As for MP3/WMA files written in any unlisted format, the contents of the files may not be played normally or the file names or folder names may not be displayed correctly.
      2. This player is compatible with multi-session discs and can play CD-Rs and CD-RWs on which MP3/WMA files have been added. However, only the first session can be played.
      3. Discs whose first session includes both music data and MP3 or WMA format data cannot be played.

    2. Standards and restrictions

      Maximum directory levels
      8 levels
      Maximum number of characters for a folder name/file name
      32 characters
      Maximum number of folders
      192 (Including empty folders, route folders, and folders that do not contain MP3/WMA files)
      Maximum number of files in a disc
      255 (Including non-MP3/WMA files)

  6. File names

    1. Only files with an extension of ".mp3" or ".wma" can be recognized and played as MP3 or WMA files.

    2. Save MP3 or WMA files with an extension of ".mp3" or ".wma".

      NOTICE:
      If non-MP3 or non-WMA files are saved with an extension of ".mp3" or ".wma", those files may be wrongly recognized as MP3 or WMA files and played. A loud noise may occur and damage to the speaker may result.


SOUND LIBRARY FUNCTION OUTLINE
  1. Up to 2000 tracks can be recorded to the HDD from audio discs.

  2. The recorded tracks will be provided with album, artist, genre and title names using the "Gracenote" Media Database ("CDDB") and stored in the sound library on the HDD.

  3. Album, artist, genre and title names for recorded tracks can be input or edited freely.

  4. These names make it possible to search for a track easily.

    HINT:
    1. Recording equipment should be used only for lawful copying. It is necessary to carefully confirm what is lawful copying in the country in which you are making a copy.
    2. Copying of copyright material such as films or music is unlawful unless permitted by a legal exception or consent granted by the owners of the rights to the content.
    3. Music recognition technology and related data are provided by "Gracenote".
    4. "Gracenote" is the industry standard in music recognition technology and related content delivery. For more information, visit www.gracenote.com.
    5. "Gracenote" and "CDDB" are registered trademarks of "Gracenote".


"Bluetooth" OUTLINE
E210030E01
  1. "Bluetooth" is a trademark owned by Bluetooth SIG. Inc.

  2. "Bluetooth" is a wireless connection technology that uses the 2.4 GHz frequency band.

    HINT:
    The communication performance of "Bluetooth" may vary depending on obstructions or radio wave conditions between communication devices, electromagnetic radiation, communication device sensitivity or antenna capacity.

  3. Hands-free function

    1. The "Bluetooth" built-in navigation receiver assembly and a "Bluetooth" compatible cellular phone*1 can be connected using a "Bluetooth" wireless connection. This enables use of the hands-free function on the cellular phone even if the phone is in a pocket or bag. For this reason, it is not necessary to use a connector or cable to connect the cellular phone.
      *1: Some versions of "Bluetooth" compatible cellular phones may not function.

  4. "Bluetooth" audio function

    1. The "Bluetooth" built-in navigation receiver assembly and a "Bluetooth" compatible portable audio player*2 can be connected using a "Bluetooth" wireless connection. This enables files stored in the portable audio player to be heard from the vehicle speakers. In addition, operations such as play/stop can be performed directly from the navigation receiver assembly.
      *2: Some versions of "Bluetooth" compatible audio players may not be able to operate the "Bluetooth" function, or music may play, but functions available using the navigation receiver assembly may be limited.

    2. Compatible "Bluetooth" audio devices

      Required "Bluetooth" specifications
      Ver. 1.1 or higher (Ver. 2.0+EDR or higher recommended)
      Compatible profiles
      1. A2DP (Advanced Audio Distribution Profile) Ver. 1.0 or higher
      2. AVRCP (Audio/Video Remote Control Profile) Ver. 1.0 or higher (Ver. 1.3 or higher recommended)
      Maximum number of audio devices that can be registered
      2

      HINT:
      The amount of remaining battery charge displayed on the navigation receiver assembly may be different from that of the portable player.


RADIO DESCRIPTION

  1. Radio frequency band

    1. Radio broadcasts use the radio frequency bands shown in the table below.
      E108734E01

  2. E108735E01
    Service area

    1. The service areas of AM and FM broadcasts are vastly different. Sometimes an AM broadcast can be received very clearly but an FM stereo broadcast cannot. FM stereo has the smallest service area, and is prone to pick up static and other types of interference such as noise.

  3. Radio reception problems

    HINT:
    In addition to static, other problems such as "phasing", "multipath" and "fade out" exist. These problems are not caused by electrical noise, but by the radio signal propagation method itself.


    1. I100011E02
      Phasing
      AM broadcasts are susceptible to electrical interference and another kind of interference called phasing. Occurring only at night, phasing is the interference created when a vehicle receives 2 radio wave signals from the same transmitter. One signal is reflected off the ionosphere and the other signal is received directly from the transmitter.

    2. I100012E02
      Multipath
      Multipath is a type of interference created when a vehicle receives 2 radio wave signals from the same transmitter. One signal is reflected off buildings or mountains and the other signal is received directly from the transmitter.

    3. I100013E02
      Fade out
      Fade out is caused by objects (buildings, mountains and other such large obstacles) that deflect away part of a signal, resulting in a weaker signal when the object is between the transmitter and vehicle. High frequency radio waves, such as FM broadcasts, are easily deflected by obstructions. Low frequency radio waves, such as AM broadcasts, are less likely to deflect.

  4. Noise problem
    Technicians must have a clear understanding about each customer's noise complaint. Use the following table to diagnose noise problems.

    Radio Frequency
    Noise Occurrence Condition
    Presumable Cause
    AM
    Noise occurs in a specific area
    Foreign noise
    AM
    Noise occurs when listening to an intermittent broadcast
    An identical program transmitted from multiple towers can cause noise where the signals overlap
    AM
    Noise occurs only at night
    Signal phasing
    FM
    Noise occurs while driving in a specified area
    Multipath noise resulting from a change in FM frequency


USB AUDIO SYSTEM FUNCTION OUTLINE
  1. The No. 1 stereo jack adapter assembly is equipped with a USB terminal. Connecting a USB device or "iPod" to the No. 1 stereo jack adapter assembly allows music files to be played. Not only is it possible to play music from a USB device with audio functions, is also possible to play MP3 or WMA music files that are stored on a USB device. In addition, "iPod" control software is installed, allowing file selection from playlists and operation using shuffle mode.

    HINT:
    1. Visual contents of an "iPod" cannot be played.
    2. Operation through the controls of a USB device or "iPod" cannot be performed while it is connected.

  2. USB audio system compatible model

    1. USB Device
      The following device formats can be used:

      Compatible USB device formats
      1. USB communication format: USB 2.0 FS (12MBPS)
      2. File format: FAT16/32 (Windows)
      3. Class: Mass storage class
      MP3 and WMA files written in any format other than those listed above may not play correctly, and their file and folder names may not be displayed correctly.
      Items related to standards and limitations are as follows:
      1. Maximum directory hierarchy: 8 levels
      2. Maximum number of folders in device: 999 (including the root folder)
      3. Maximum number of files in device: 65025
      4. Maximum number of files per folder: 255

    2. "iPod"
      "iPod" is a trademark of Apple Inc., registered in the U.S. and other countries.

      Supported "iPod" Models and Firmware Versions 
      Supported "iPod" Model
      Supported Firmware Version
      "iPod" 5th generation
      Ver. 1.2.0 or higher
      "iPod Nano" 1st generation
      Ver. 1.3.0 or higher
      "iPod Nano" 2nd generation
      Ver. 1.1.2 or higher
      "iPod Nano" 3rd generation
      Ver. 1.0.0 or higher
      "iPod touch" 1st generation
      Ver. 1.1.0 or higher
      "iPod classic" 1st generation
      Ver. 1.0.0 or higher
      Unsupported "iPod" Models 
      Unsupported Models
      "iPod shuffle"
      "iPhone"
      "iPod" 4th generation and earlier models
      "iPod mini"
      "iPod photo"
      Items related to standards and limitations are as follows:
      1. Maximum number of lists in device: 9999
      2. Maximum number of songs in device: 65535
      3. Maximum number of songs per list: 65535

      HINT:
      1. "iPod" models and firmware versions that are not listed in "Supported "iPod" Models and Firmware Versions" may not function, or may not function correctly.
      2. Depending on the generation of "iPod" used, response to commands from the vehicle may be delayed.


AUTOMATIC SOUND LEVELIZER (ASL) FUNCTION OUTLINE
  1. The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based upon vehicle speed signals that it receives from the combination meter.


COMMUNICATION SYSTEM

  1. AVC-LAN Outline
    E176501E23

    1. Components of the navigation system communicate with each other via the AVC-LAN.

    2. The AVC-LAN uses a twisted pair of wires for its communication lines.

    3. The master unit of the AVC-LAN is the navigation receiver assembly.

      HINT:
      1. The navigation receiver assembly has the resistance (60 to 80 Ω) necessary for communication.
      2. If a short or open circuit occurs in the AVC-LAN circuit, communication is interrupted and system will not operate normally.


DIAGNOSTIC FUNCTION OUTLINE
  1. The navigation system has a diagnostic function (the result is indicated on the master unit).


DIAGNOSIS DISPLAY DETAILED DESCRIPTION

HINT:
  1. This section contains a detailed description of displays in diagnostic mode.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Service Menu Screen
    E176694

    HINT:
    Some items are grayed out or not displayed based on the device settings.

  2. Failure Diagnosis Screen
    E176701

    HINT:
    Some items are grayed out or not displayed based on the device settings.


    1. System Check Mode Screen
      E210060E01

      1. *1: Device Name List No. 1

        HINT:
        1. Device Name List No. 1 displays some of the devices that make up the navigation system.
        2. The names of the components from Device Name List No. 1 are shown in the following table.
          Name
          Component
          Connection Method
          AVN
          Navigation receiver assembly
          -
          USB-BOX
          Multi-media interface ECU
          Communication line for AVC-LAN

      1. *2: Check Result

        HINT:
        Result codes for all devices are displayed.
        Result
        Meaning
        Action
        OK
        The device does not respond with a DTC.
        -
        EXCH
        The device responds with a "replace"-type DTC.
        Look up the DTC in "Unit Check Mode" and replace the device.
        CHEK
        The device responds with a "check"-type DTC.
        Look up the DTC in "Unit Check Mode".
        NCON
        The device was previously present, but does not respond in diagnostic mode.
        - Check power supply wire harness of the device.
        - Check the AVC-LAN of the device.
        NRES
        The device responds in diagnostic mode, but gives no DTC information.
        - Check power supply wire harness of the device.
        - Check the AVC-LAN of the device.

      1. *3: Memory Clear

        HINT:
        1. Present and history DTCs and registered connected device names are cleared.
        2. Press the "Memory CLR" switch for 3 seconds.

      1. *4: Recheck

        HINT:
        1. A system check will be performed again after the memory is cleared.
        2. The "Recheck" switch will dim during a system check.

      1. *5: Device Name List No. 2

        HINT:
        1. Device Name List No. 2 displays some of the devices that make up the navigation system.
        2. The names of the components from Device Name List No. 2 are shown in the following table.
          Name
          Component
          Connection Method
          MIC
          Telephone microphone assembly
          Vehicle wire harness
          AUX
          No. 1 stereo jack adapter assembly
          Vehicle wire harness

    2. Unit Check Mode Screen
      E176511E02

      Screen Description 
      Display
      Content
      *1: Device name
      Target device
      *2: History DTC
      Diagnostic memory results and stored DTCs are displayed.
      *3: Present DTC
      DTCs output in the service check are displayed.
      *4: DTC
      DTC (Diagnostic Trouble Code)
      *5: Timestamp
      The time and date of history DTCs are displayed. (The year is displayed in 2-digit format.)
      *6: Diagnosis clear switch
      Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.)

      HINT:
      A maximum of 6 DTCs can be displayed for history and present DTCs.

  3. Function Check/Setting Screen
    E210138

    HINT:
    Some items are grayed out or not displayed based on the device settings.


    1. Microphone & Voice Recognition Check Screen
      E176507E01

      Screen Description 
      Display
      Content
      *1: Microphone input level meter
      Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
      *2: Recording switch
      Starts recording.
      *3: Stop switch
      Stops recording and playing.
      *4: Play switch
      Plays the recorded voice.
      *5: Recording indicator
      Comes on while recording.

      HINT:
      1. The microphone is active at all times when this screen is displayed.
      2. Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.
      3. While recording or playing, the switches other than the stop switch cannot be pushed.
      4. When no recording is present, the play switch cannot be pushed.
      5. Recording will stop after 5 seconds or when the stop switch is pushed.

    2. GPS Information Screen
      E176509E01

      1. *1: Satellite information
        Information from a maximum of 12 satellites is displayed on the screen. This information includes the target GPS satellite number, elevation angle, direction and signal level.
      1. *2: Receiving condition
        Screen Description 
        Display
        Content
        T
        The system is receiving a GPS signal, but is not using it for location.
        P
        The system is using the GPS signal for location.
        -
        The system cannot receive a GPS signal.
      1. *3: Measurement status
        Screen Description 
        Display
        Content
        2D
        2-dimensional location method is being used.
        3D
        3-dimensional location method is being used.
        NG
        Location data cannot be used.
        Error
        Reception error has occurred.
        -
        Any other state.
      1. *4: Position information
        Screen Description 
        Display
        Content
        Position
        Latitude and longitude information on the current position is displayed.
      1. *5: Date information
        Screen Description 
        Display
        Content
        Date
        The date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT).

    3. Vehicle Sensors Screen
      E176506E01

      Vehicle Signal 
      Display
      Content
      *1: SPD
      SPD signal condition is displayed.
      Sensor Signal 
      Display
      Content
      *2: Gyro sensor
      Gyro sensor output condition is displayed.

      HINT:
      Signals are updated once per second only when vehicle sensor signals change.

    4. Vehicle Signal Check Mode Screen
      E176505

      Screen Description 
      Display
      Content
      Battery
      Battery voltage is displayed.
      IG
      Ignition switch ON/OFF state is displayed.
      PKB
      Parking brake ON/OFF state is displayed.
      REV
      Reverse signal ON/OFF state is displayed.
      SPEED
      Vehicle speed is displayed in km/h.
      TAIL
      Tail signal (Light control switch) ON/OFF state is displayed.

      HINT:
      1. Only items sending vehicle signals will be displayed.
      2. This screen is updated once per second when vehicle input signals change.

    5. Sound Library Information Screen
      E176734E01

      Screen Description 
      Display
      Content
      *1: Recording function setting for HDD
      Recording to HDD permitted (ON)/not permitted (OFF)
      *2: Media database version
      Media database version currently installed on HDD
      *3: Number of albums
      Number of albums recorded in HDD
      *4: Number of tracks
      Number of tracks recorded in HDD
      *5: Free space in HDD
      Free space in HDD partition for sound library

← SYSTEM DIAGRAM (from Jul 2010)HOW TO PROCEED WITH TROUBLESHOOTING (Jul 2010 – Jun 2012) →