2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL FRONT COIL SPRING LOWER INSULATOR

  1. C165910E01
    Install the front coil spring lower insulator to the front shock absorber.

    NOTICE:
    Make sure that the positioning pins on the front coil spring lower insulator are inserted into the holes in the front shock absorber.


2. INSTALL FRONT SPRING BUMPER

  1. C165909
    Install the front spring bumper to the front shock absorber.


3. INSTALL FRONT COIL SPRING

  1. C265549E01
    Attach SST to the front coil spring and secure it in a vise.
    SST
    09727-30021   (09727-00010, 09727-00031)
    09727-00050  

  1. C263591
    Attach the arm of SST to the diameter of the front coil spring.

    CAUTION:
    1. Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.
    2. Make sure that the claws of the hooks are securely attached.

  1. Using SST, compress the front coil spring.

    CAUTION:
    1. If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.
    2. Do not compress the spring until the coil springs contact each other.
    3. Do not use an impact wrench. It will damage SST.

  1. C267416E01
    Install the front coil spring to the front shock absorber assembly.

    NOTICE:
    Make sure that the end of the front coil spring is positioned in the depression of the front lower coil spring insulator.


4. INSTALL FRONT COIL SPRING UPPER INSULATOR

  1. C269411E01
    Install the front coil spring upper insulator as shown in the illustration.

    HINT:
    Any misalignment between the front shock absorber lower bracket and the alignment mark must be +/- 5°.


5. INSTALL FRONT COIL SPRING UPPER SEAT

  1. C269413E01
    Install the front coil spring upper seat with the mark facing to the outside of the vehicle.

    HINT:
    Any misalignment between the front shock absorber lower bracket and the alignment mark must be +/- 5°.


6. INSTALL FRONT SUSPENSION SUPPORT BEARING

  1. C269412E01
    Install the front suspension support bearing as shown in the illustration.


7. INSTALL FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

  1. C269414E01
    Install the front suspension support sub-assembly as shown in the illustration.

    HINT:
    Check that the slot on the piston rod and the slot on the front suspension support sub-assembly are aligned.

  1. Temporarily tighten a new front support to front shock absorber nut.


8. INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

  1. C165912
    Install the front shock absorber with coil spring (upper side) with the nut and 2 spacers.

    Torque:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }

  1. C165908
    Install the front shock absorber with coil spring (lower side) to the steering knuckle and insert the 2 bolts and 2 nuts.

    Torque:
    290 N*m{ 2956 kgf*cm , 214 ft.*lbf }

    NOTICE:
    When installing the nuts, keep the bolts from rotating.


9. INSTALL FRONT STABILIZER LINK ASSEMBLY

  1. C165915
    Install the front stabilizer link assembly to the front shock absorber with the nut.

    Torque:
    74 N*m{ 755 kgf*cm , 55 ft.*lbf }

    NOTICE:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud bolt.


10. INSTALL FRONT SPEED SENSOR

  1. C167708
    Install the front speed sensor and front flexible hose with the bolt.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

    NOTICE:
    Do not twist the front speed sensor when installing it.

  1. Install the clamp.


11. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

  1. C165926E01
    Install the outer cowl top panel sub-assembly with the 8 bolts and 6 nuts.

    Torque:
    Nut A:
    85 N*m{ 866 kgf*cm , 63 ft.*lbf }
    Bolt B:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }
    Nut C:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }

  1. C165925
    Engage the 4 clamps.


12. FULLY TIGHTEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

  1. C165911
    Fully tighten the front support to front shock absorber nut.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }


13. INSTALL WINDSHIELD WIPER MOTOR AND LINK

  1. E150150
    Install the windshield wiper motor and link assembly with the 4 bolts.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Connect the connector.


14. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. Engage the 20 claws.

    E150149

  1. Install the cowl top ventilator louver sub-assembly with the 2 clips.

  1. E150146
    Engage the 2 claws and connect the front fender to cowl side seal LH.

  1. E150147
    Engage the 2 claws and connect the front fender to cowl side seal RH.


15. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E147125E01
    Install the front wiper arm and blade assembly RH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    25.6 mm (1.00 in.)


16. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH
  1. Operate the wiper and stop the windshield wiper motor at the automatic stop position.

  1. When reinstalling:

    1. E112237E01
      Clean the wiper arm serrations.

    2. Clean the wiper pivot serrations with a wire brush.

  1. E152618E01
    Install the front wiper arm and blade assembly LH with the nut to the position shown in the illustration.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold the wiper arm by hand when tightening the nut.

    Area
    Measurement
    A
    31.9 mm (1.26 in.)

  1. Operate the front wipers while spraying washer fluid onto the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


17. INSTALL FRONT WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


18. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
Inspect and adjust front wheel alignment (Click here).
← INSTALLATION (Aug 2008 – Jun 2010)DISPOSAL (from May 2007) →