2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Illumination Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E150793E12

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).


1. CHECK ILLUMINATION
  1. Check if the illumination for the navigation receiver assembly, steering pad switch assembly, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the tail or head position.

    Result:
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch assembly.
    A
    Illumination comes on for all components except navigation receiver assembly.
    B
    No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.).
    C



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)
A


2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE SUB-ASSEMBLY)
  1. Disconnect the D53 spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D53-12 (IL+2) - Body ground
    Light control switch in the tail or head position
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT SPIRAL CABLE SUB-ASSEMBLY

  1. E168547E92
    Disconnect the z2 steering pad switch assembly and D53 spiral cable sub-assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-8 (EAU) - D53-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-5 (IL+2) - D53-12 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Refer to the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *b
    Steering Pad Switch Side
    *c
    Vehicle Side



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - NAVIGATION RECEIVER ASSEMBLY)
  1. Disconnect the E2 navigation receiver assembly.

  1. Disconnect the D53 spiral cable sub-assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-6 (SWG) - D53-4 (EAU)
    Always
    Below 1 Ω
    D53-4 (EAU) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the z2 steering pad switch assembly connector.

  1. Connect a positive (+) lead from the battery to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch assembly connector.E136178E05

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.

    Text in Illustration 
    *a
    Component without harness connected
    (Steering Pad Switch Assembly)
    -
    -



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

6. CHECK HARNESS AND CONNECTOR (BATTERY - NAVIGATION RECEIVER ASSEMBLY)
  1. Disconnect the E6 navigation receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E6-10 (ILL+) - Body ground
    Light control switch in the tail or head position
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the E7 navigation receiver assembly connector.

  1. Disconnect the E1 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-5 (ILL-) - E1-30 (ILL-)
    Always
    Below 1 Ω
    E7-5 (ILL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Illumination Circuit (Aug 2008 – Jun 2010)Parking Brake Switch Circuit (May 2007 – Jul 2008) →