2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Illumination Circuit

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM

E150793E02

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).


1. CHECK ILLUMINATION
  1. Check if the illumination for the navigation receiver assembly, steering pad switch, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.

    Result:
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except navigation receiver assembly.
    B
    No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.).
    C
    Illumination comes on only for steering pad switch and glove box.
    D



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)

D
GO TO METER / GAUGE SYSTEM (Click here)
A


2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE)

  1. E126428E11
    Disconnect spiral cable connector D53.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D53-12 (IL+2) - Body ground
    Light control switch in TAIL or HEAD
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT SPIRAL CABLE

  1. E150780E06
    Disconnect the steering pad switch and spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-8 (EAU) - D53-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-5 (IL+2) - D53-12 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Refer to the pages shown in the brackets.

    HINT:
    1. REMOVAL (Click here)
    2. INSTALLATION (Click here)



NG
REPLACE SPIRAL CABLE (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - NAVIGATION RECEIVER ASSEMBLY)

  1. E141021E14
    Disconnect navigation receiver assembly connector E2 and spiral cable connector D53.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-6 (SWG) - D53-4 (EAU)
    Always
    Below 1 Ω
    E2-6 (SWG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the steering pad switch assembly connector.

  1. Connect the positive (+) lead to terminal IL+2 and the negative (-) lead to terminal EAU of the steering pad switch connector.E136178E04

  1. Check if the illumination for the steering pad switch comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

6. CHECK HARNESS AND CONNECTOR (BATTERY - NAVIGATION RECEIVER ASSEMBLY)

  1. E141019E31
    Disconnect navigation receiver assembly connector E6.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E6-10 (ILL+) - Body ground
    Light control switch in TAIL or HEAD
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER)

  1. E153694E01
    Disconnect navigation receiver assembly connector E7.

  1. E143742E98
    Disconnect combination meter connector E1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-5 (ILL-) - E1-30 (ILL-)
    Always
    Below 1 Ω
    E7-5 (ILL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Steering Pad Switch Circuit (from Jul 2010)Illumination Circuit (Aug 2008 – Jun 2010) →