2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Light Control Switch Circuit

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The main body ECU receives the following signals:
  1. Light control switch TAIL, HEAD, or AUTO signal
  2. Dimmer switch HIGH or HIGH FLASH (PASS) signal
  3. Front fog light switch signal
  4. Rear fog light switch signal

HINT:
When performing troubleshooting, inspect the switch that is related to the malfunction. For example, if both right and left low beam headlights do not illuminate, read the light control switch HEAD signal value only in the data list. If the value is normal, perform the headlight relay active test.


WIRING DIAGRAM

E121534E16

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Select the following menu items: Body Electrical / Main Body / Data List.

  1. Read the displays on the intelligent tester.

    Main Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Dimmer Hi SW
    Dimmer switch HIGH signal / ON or OFF
    ON: Dimmer switch in HIGH
    OFF: Dimmer switch in LOW
    -
    Passing Light SW
    Dimmer switch FLASH signal / ON or OFF
    ON: Dimmer switch in HIGH FLASH (PASS)
    OFF: Dimmer switch not in HIGH FLASH (PASS)
    -
    Front Fog Light SW
    Front fog light switch signal / ON or OFF
    ON: Front fog light switch ON
    OFF: Front fog light switch OFF
    -
    Rear Fog Light SW
    Rear fog light switch signal / ON or OFF
    ON: Rear fog light switch ON
    OFF: Rear fog light switch OFF
    -
    Light Auto SW
    Light control switch AUTO signal / ON or OFF
    ON: Light control switch in AUTO
    OFF: Light control switch not in AUTO
    -
    Headlight SW
    Light control switch HEAD signal / ON or OFF
    ON: Light control switch in HEAD
    OFF: Light control switch not in HEAD
    -
    Taillight SW
    Light control switch TAIL signal / ON or OFF
    ON: Light control switch in TAIL or HEAD
    OFF: Light control switch in neither TAIL nor HEAD
    -

    OK:
    Normal conditions listed above are displayed.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY
  1. Inspect the headlight dimmer switch assembly (Click here).

    OK:
    Headlight dimmer switch assembly is normal.



NG
REPLACE HEADLIGHT DIMMER SWITCH ASSEMBLY
OK


3. CHECK HARNESS AND CONNECTOR (SWITCH - INSTRUMENT PANEL J/B AND BODY GROUND)

  1. for LHD:

    1. E151685E05
      Disconnect the D12 headlight dimmer switch assembly connector.

    2. Disconnect the D6 and D7 main body ECU connectors.

    3. Disconnect the 1N instrument panel junction block connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D12-2 (B) - D6-9 (RFOG)
      Always
      Below 1 Ω
      D12-4 (BFG) - D6-28 (FFOG)
      Always
      Below 1 Ω
      D12-11 (HU) - 1N-2 (HU)
      Always
      Below 1 Ω
      D12-17 (HF) - D7-13 (HF)
      Always
      Below 1 Ω
      D12-18 (T) - D7-23 (TAIL)
      Always
      Below 1 Ω
      D12-19 (A) - D7-21 (A)
      Always
      Below 1 Ω
      D12-20 (H) - D6-17 (HEAD)
      Always
      Below 1 Ω
      D12-2 (B) - Body ground
      Always
      10 kΩ or higher
      D12-3 (LFG) - Body ground
      Always
      10 kΩ or higher
      D12-4 (BFG) - Body ground
      Always
      10 kΩ or higher
      D12-11 (HU) - Body ground
      Always
      10 kΩ or higher
      D12-17 (HF) - Body ground
      Always
      10 kΩ or higher
      D12-18 (T) - Body ground
      Always
      10 kΩ or higher
      D12-19 (A) - Body ground
      Always
      10 kΩ or higher
      D12-20 (H) - Body ground
      Always
      10 kΩ or higher
      D12-12 (EL) - Body ground
      Always
      Below 1 Ω
      D12-3 (LFG) - Body ground
      Always
      Below 1 Ω

  1. for RHD:

    1. E151685E04
      Disconnect the D12 headlight dimmer switch assembly connector.

    2. Disconnect the D6 and D7 main body ECU connectors.

    3. Disconnect the 1N instrument panel junction block connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      D12-13 (T) - D7-23 (TAIL)
      Always
      Below 1 Ω
      D12-7 (BFG) - D6-28 (FFOG)
      Always
      Below 1 Ω
      D12-11 (H) - D6-17 (HEAD)
      Always
      Below 1 Ω
      D12-12 (A) - D7-21 (A)
      Always
      Below 1 Ω
      D12-14 (HF) - D7-13 (HF)
      Always
      Below 1 Ω
      D12-20 (HU) - 1N-2 (HU)
      Always
      Below 1 Ω
      D12-13 (T) - Body ground
      Always
      10 kΩ or higher
      D12-7 (BFG) - Body ground
      Always
      10 kΩ or higher
      D12-11 (H) - Body ground
      Always
      10 kΩ or higher
      D12-12 (A) - Body ground
      Always
      10 kΩ or higher
      D12-14 (HF) - Body ground
      Always
      10 kΩ or higher
      D12-20 (HU) - Body ground
      Always
      10 kΩ or higher
      D12-19 (EL) - Body ground
      Always
      Below 1 Ω
      D12-8 (LFG) - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← Rear Fog Light Circuit (from Jul 2010)Light Control Switch Circuit (Aug 2008 – Jun 2010) →