2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Rear Fog Light Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The main body ECU controls the rear fog relay when a signal is received from the headlight dimmer switch assembly.

WIRING DIAGRAM

E136323E07

INSPECTION PROCEDURE


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Select the following menu items: Body Electrical / Main Body / Active Test.

  1. Check that the relay operate.

    Main Body: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Rear Fog Light Relay
    Rear fog light relay
    ON/OFF
    -

    OK:
    Rear fog light relay operates. (Rear fog light comes on.)



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT FUSE (RR FOG)
  1. Remove the RR FOG fuse from the instrument panel junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    RR FOG fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3. INSPECT REAR FOG LIGHT RELAY (RR FOG)

  1. B060778E87
    Remove the rear fog light relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Voltage is not applied between terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Apply the battery voltage between terminals 1 and 2
    Below 1 Ω



NG
REPLACE REAR FOG LIGHT RELAY
OK


4. CHECK HARNESS AND CONNECTOR (BATTERY - REAR FOG LIGHT RELAY)

  1. E151665E01
    Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    Rear fog light relay terminal 5 - Body ground
    Always
    11 to 14 V
    Rear fog light relay terminal 2 - Body ground
    Light control switch OFF → TAIL
    Below 1 V → 11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT RELAY - MAIN BODY ECU)

  1. Disconnect the D8 main body ECU connector.E151666E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    Rear fog light relay terminal 1 - D8-14 (RFGO)
    Always
    Below 1 Ω
    D8-14 (RFGO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

  1. Reconnect the D8 main body ECU connector.E142675E06

  1. Install the rear fog light relay to the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D8-14 (RFGO) - Body ground
    Light control switch in HEAD and rear fog light switch OFF → ON
    11 to 14 V → Below 1 V



NG
REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (REAR FOG LIGHT RELAY - BODY GROUND)


← Rear Fog Light Circuit (Aug 2008 – Jun 2010)Light Control Switch Circuit (May 2007 – Jul 2008) →