1.
INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Power Seat)
Install the front seat inner belt assembly with the nut.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
NOTICE:
Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect each connector and clamp.
2.
INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat)
Install the front seat inner belt assembly with the nut.
Torque:
42 N*m{
428 kgf*cm
, 31 ft.*lbf
}
NOTICE:
Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.
Connect each connector and clamp.
3.
INSTALL FRONT SEAT ASSEMBLY (for Power Seat)
Place the front seat assembly in the cabin.
NOTICE:
Be careful not to damage the vehicle body.
Connect the connectors under the seat.
Connect the cable to the negative (-) battery terminal.
NOTICE:
When reconnected the cable, some systems need to be initialized (Click here).
Temporarily install the front seat assembly with the 4 bolts.
Operate the power seat switch knob and move the seat to the rearmost position.
Tighten the 2 bolts on the front side of the seat.
Torque:
37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
HINT:
Tighten the bolts in the order indicated in the illustration.
Operate the power seat switch knob and move the seat to the foremost position.
Tighten the 2 bolts on the rear side of the seat.
Torque:
37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
HINT:
Tighten the bolts in the order indicated in the illustration.
4.
INSTALL REAR INNER SEAT TRACK COVER (for Power Seat)
Engage the 2 claws and install the rear inner seat track cover.
5.
INSTALL REAR OUTER SEAT TRACK COVER (for Power Seat)
Engage the 2 claws and install the rear outer seat track cover.
6.
INSTALL FRONT INNER SEAT TRACK COVER (for Power Seat)
Operate the power seat switch knob and move the seat to the rearmost position.
Engage the 2 claws and install the front inner seat track cover.
7.
INSTALL FRONT OUTER SEAT TRACK COVER (for Power Seat)
Engage the 2 claws and install the front outer seat track cover.
8.
INSTALL FRONT SEAT HEADREST ASSEMBLY (for Power Seat)
9.
INSTALL FRONT SEAT ASSEMBLY (for Manual Seat)
Place the front seat assembly in the cabin.
NOTICE:
Be careful not to damage the vehicle body.
Connect the connectors under the seat.
Temporarily install the front seat assembly with the 4 bolts.
Lift up the seat track adjusting handle and move the seat to the rearmost position.
Tighten the 2 bolts on the front side of the seat.
Torque:
37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
HINT:
Tighten the bolts in the order indicated in the illustration.
Lift up the seat track adjusting handle and move the seat to the foremost position.
Tighten the 2 bolts on the rear side of the seat.
Torque:
37 N*m{
377 kgf*cm
, 27 ft.*lbf
}
HINT:
Tighten the bolts in the order indicated in the illustration.
10.
INSPECT FRONT SEAT SLIDE ADJUSTER LOCK (for Manual Seat)
During sliding operation of the front seat, check that the left and right adjusters move together smoothly and lock simultaneously. If the seat adjusters do not lock simultaneously, loosen the bolts securing the seat to adjust the adjuster position.