2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Steering Pad Switch Circuit

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.
Therefore, the radio receiver cannot be operated using the steering pad switch, and also the radio receiver itself cannot function.

WIRING DIAGRAM

E160425E24

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the supplemental restraint system (Click here).


1. INSPECT RADIO RECEIVER

  1. E160426E35
    Disconnect the radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-7 (SW1) - E2-6 (SWG)
    No switch pushed
    95 to 105 kΩ
    E2-7 (SW1) - E2-6 (SWG)
    Seek+ switch pushed
    Below 2.5 Ω
    E2-7 (SW1) - E2-6 (SWG)
    Seek- switch pushed
    312 to 345 Ω
    E2-7 (SW1) - E2-6 (SWG)
    Volume+ switch pushed
    950 to 1050 Ω
    E2-7 (SW1) - E2-6 (SWG)
    Volume- switch pushed
    2954 to 3265 Ω
    E2-8 (SW2) - E2-6 (SWG)
    No switch pushed
    95 to 105 kΩ
    E2-8 (SW2) - E2-6 (SWG)
    MODE switch pushed
    Below 2.5 Ω
    E2-8 (SW2) - E2-6 (SWG)*1
    Voice switch pushed
    2954 to 3265 Ω
    E2-8 (SW2) - E2-6 (SWG)*1
    On hook switch pushed
    312 to 345 Ω
    E2-8 (SW2) - E2-6 (SWG)*1
    Off hook switch pushed
    950 to 1050 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio Receiver)
    1. *1: w/ Telephone Microphone Assembly



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the steering pad switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.E136177E22

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-10 (AU1) - z2-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z2-10 (AU1) - z2-8 (EAU)
    Seek+ switch pushed
    Below 2.5 Ω
    z2-10 (AU1) - z2-8 (EAU)
    Seek- switch pushed
    312 to 345 Ω
    z2-10 (AU1) - z2-8 (EAU)
    Volume+ switch pushed
    950 to 1050 Ω
    z2-10 (AU1) - z2-8 (EAU)
    Volume- switch pushed
    2954 to 3265 Ω
    z2-9 (AU2) - z2-8 (EAU)
    No switch pushed
    95 to 105 kΩ
    z2-9 (AU2) - z2-8 (EAU)
    MODE switch pushed
    Below 2.5 Ω
    z2-9 (AU2) - z2-8 (EAU)*1
    Voice switch pushed
    2954 to 3265 Ω
    z2-9 (AU2) - z2-8 (EAU)*1
    On hook switch pushed
    312 to 345 Ω
    z2-9 (AU2) - z2-8 (EAU)*1
    Off hook switch pushed
    950 to 1050 Ω

    1. *1: w/ Telephone Microphone Assembly
    Text in Illustration 
    *A
    w/ Telephone Microphone Assembly
    *a
    Component without harness connected
    (Steering Pad Switch Assembly)
    *b
    Volume+
    *c
    Volume-
    *d
    Seek-
    *e
    MODE
    *f
    Seek+
    *g
    On hook
    *h
    Off hook
    *i
    Voice



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


3. INSPECT SPIRAL CABLE

  1. E166173E38
    Disconnect the steering pad switch assembly and spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-8 (EAU) - D53-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-10 (AU1) - D53-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-9 (AU2) - D53-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *a
    Component without harness connected
    (Spiral Cable)
    *b
    Steering Pad Switch Assembly Side
    *c
    Vehicle Side



NG
REPLACE SPIRAL CABLE (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)


← Steering Pad Switch Circuit (Aug 2008 – Jun 2010)Illumination Circuit (May 2007 – Jul 2008) →