2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Steering Pad Switch Circuit

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

This circuit sends an operation signal from the steering pad switch to the radio receiver.
If there is an open in the circuit, the audio system cannot be operated using the steering pad switch.
If there is a short in the circuit, the same condition as to when a switch is continuously depressed occurs.
Therefore, the radio receiver cannot be operated using the steering pad switch, and also the radio receiver itself cannot function.

WIRING DIAGRAM

E141049E06

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precautionary notice for the Supplemental Restraint System (Click here).


1. INSPECT RADIO RECEIVER

  1. E141020E14
    Disconnect the radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-7 (SW1) - E2-6 (SWG)
    No switch is pushed
    Approx. 100 kΩ
    E2-7 (SW1) - E2-6 (SWG)
    SEEK+ switch: push
    0 to 2.5 Ω
    E2-7 (SW1) - E2-6 (SWG)
    SEEK- switch: push
    Approx. 0.3 kΩ
    E2-7 (SW1) - E2-6 (SWG)
    VOL+ switch: push
    Approx. 1 kΩ
    E2-7 (SW1) - E2-6 (SWG)
    VOL- switch: push
    Approx. 3.1 kΩ
    E2-8 (SW2) - E2-6 (SWG)
    No switch is pushed
    Approx. 100 kΩ
    E2-8 (SW2) - E2-6 (SWG)
    MODE switch: push
    0 to 2.5 Ω



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the steering pad switch assembly connector.

  1. Measure the resistance according to the values in the table below.E131853E03

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-10 (AU1) - z2-8 (EAU)
    No switch is pushed
    Approx. 100 kΩ
    z2-10 (AU1) - z2-8 (EAU)
    SEEK+ switch: push
    0 to 2.5 Ω
    z2-10 (AU1) - z2-8 (EAU)
    SEEK- switch: push
    Approx. 0.3 kΩ
    z2-10 (AU1) - z2-8 (EAU)
    VOL+ switch: push
    Approx. 1 kΩ
    z2-10 (AU1) - z2-8 (EAU)
    VOL- switch: push
    Approx. 3.1 kΩ
    z2-9 (AU2) - z2-8 (EAU)
    No switch is pushed
    Approx. 100 kΩ
    z2-9 (AU2) - z2-8 (EAU)
    MODE switch: push
    0 to 2.5 Ω



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


3. INSPECT SPIRAL CABLE

  1. I039337E90
    Disconnect the steering pad switch and spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Spiral Cable Position
    Specified Condition
    z2-8 (EAU) - D53-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-10 (AU1) - D53-6 (AU1)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z2-9 (AU2) - D53-5 (AU2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the page shown in the brackets.

    HINT:
    1. REMOVAL (Click here)
    2. INSTALLATION (Click here)



NG
REPLACE SPIRAL CABLE (Click here)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE - RADIO RECEIVER)


← Vehicle Speed Signal Circuit between Radio Receiver and Combination Meter (from Jul 2010)Steering Pad Switch Circuit (Aug 2008 – Jun 2010) →