2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Radio Broadcast cannot be Received or Poor Reception

Circuit diagnosis · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

WIRING DIAGRAM

E186662E16

INSPECTION PROCEDURE


1. CHECK NAVIGATION RECEIVER ASSEMBLY
  1. Check the radio automatic station search function.

    1. Check the radio automatic station search function by activating it.

      Result:
      Result
      Proceed to
      Automatic station search function does not stop
      A
      Automatic station search function stops on a station
      B



B
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
A


2. CHECK OPTIONAL COMPONENTS
  1. Check optional components (sun-shade film, telephone antenna, etc.).

    1. Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.

      Result:
      Result
      Proceed to
      Optional components are installed
      A
      Optional components are not installed
      B

      NOTICE:
      Do not remove optional components without the permission of the customer.



B
Go to step 3
A

REMOVE OPTIONAL COMPONENTS AND CHECK AGAIN (SEE NOTICE ABOVE)

3. CHECK NAVIGATION RECEIVER ASSEMBLY

  1. E050367
    Preparation for check
    1. Remove the antenna plug from the navigation receiver assembly.

  1. Check for noise

    1. Turn the ignition switch to ACC with the navigation receiver assembly connector connected.

    2. Turn the radio on and tune into AM mode.

    3. Place a screwdriver, thin wire, or other metal object on the navigation receiver assembly antenna jack and check that noise can be heard from the speaker.

      OK:
      Noise occurs.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4. CHECK WINDOW GLASS ANTENNA WIRE

  1. E111994E01
    Check for continuity of the window glass antenna wire.

    HINT:
    Check for continuity at the center of each antenna wire as shown in the illustration.

    NOTICE:
    When cleaning the glass, wipe it in the direction of the wire with a soft dry cloth. Take care not to damage the wire. Do not use detergents or glass cleaners with abrasive ingredients. When measuring resistance, wrap a piece of tin foil around the tip of each probe and press the foil against the wire with your finger, as shown in the illustration.

    OK:
    There is continuity in the antenna.



NG
REPAIR WINDOW GLASS ANTENNA WIRE (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - AMPLIFIER ANTENNA ASSEMBLY)
  1. Disconnect the E6 navigation receiver assembly connector.

  1. Disconnect the E5 amplifier antenna assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-8 (ANT) - E5-1 (B)
    Always
    Below 1 Ω
    E5-1 (B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT NAVIGATION RECEIVER ASSEMBLY

  1. E168580E40
    Reconnect the E5 navigation receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E5-1 (B) - Body ground
    Ignition switch ON
    Radio switch on
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Amplifier Antenna Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


7. CHECK ANTENNA CORD SUB-ASSEMBLY
  1. Remove the antenna plug of the navigation receiver assembly and amplifier antenna assembly.

  1. Measure the resistance between the amplifier antenna assembly and navigation receiver assembly to check for an open circuit in the antenna cord sub-assembly.

    Standard Resistance:
    Below 1 Ω

  1. Measure the resistance between the antenna cord sub-assembly and body ground to check for a short circuit in the antenna cord sub-assembly.

    Standard Resistance:
    10 kΩ or higher



NG
REPLACE ANTENNA CORD SUB-ASSEMBLY (Click here)
OK


8. REPLACE AMPLIFIER ANTENNA ASSEMBLY
  1. Replace the amplifier antenna assembly and check if radio broadcasts can be received normally (Click here).

    OK:
    Radio broadcasts can be received.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK

NORMAL OPERATION


← Radio Broadcast cannot be Received or Poor Reception (Aug 2008 – Jun 2010)Illumination for Panel Switch does not Come on with Tail Switch ON (May 2007 – Jul 2008) →