2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Fuel Receiver Gauge Malfunction

Circuit diagnosis · Vehicles built Jul 2010 – Jun 2012

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 Jul 2010 – Jun 2012 from Jul 2012

DESCRIPTION

  1. The meter CPU uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge will vary between approximately 4 Ω with the float at the full position, and 110 Ω with the float at the empty position. The meter outputs battery voltage through two 220 Ω resistors that are mounted in parallel inside the meter CPU. The meter CPU measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in parallel in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of battery voltage.

HINT:
The fuel level warning light will come on when the fuel level is below 11.0 liters.


WIRING DIAGRAM

E152381E01

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).


Result:
Result
Proceed to
CAN communication DTC is not output.
A
CAN communication DTC is output.
B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter following menus: Body Electrical / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Fuel Meter Operation
    Fuel receiver gauge
    EMPTY, 1/2, FULL
    -

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


Go to step 4

3. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter following menus: Body Electrical / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input
    Fuel input signal Min.: 0, Max.: 127.5
    Fuel gauge indicates (E): 7.5 (L)
    Fuel gauge indicates (1/2): 35.0 (L)
    Fuel gauge indicates (F): 62.9 (L)
    -

    OK:
    Fuel value signal displayed on the tester is almost the same as needle indication.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SENDER GAUGE ASSEMBLY)

  1. E152442E03
    Disconnect the E1 and fuel sender gauge assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E1-34 (FR) - 2
    Always
    Below 1 Ω
    E1-19 (FE) - 1
    Always
    Below 1 Ω
    2 - Body ground
    Always
    10 kΩ or higher
    E1-34 (FR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT FUEL SENDER GAUGE ASSEMBLY

  1. E146925E01
    Disconnect the fuel sender gauge connector.

  1. Measure the resistance between terminals 1 and 2 of the connector according to the value(s) in the table below.

    Standard resistance:
    Float Level
    Resistance (Ω)
    F
    3.0 to 5.0
    Between E and F
    3.0 to 4.0 (Gradually changes)
    E
    109.0 to 111.0

  1. Remove the fuel sender gauge assembly (Click here).

  1. Check that the float moves smoothly between F and E.

  1. Check if the fuel sender gauge arm is deformed.



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY (Click here)
OK


6. REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new one or a normal one (Click here).

    OK:
    The operation of the combination meter assembly returns to normal.



NG
REPLACE ECM (Click here)
OK

END


← Fuel Receiver Gauge Malfunction (Aug 2008 – Jun 2010)Fuel Receiver Gauge Malfunction (from Jul 2012) →