2007-2013 Highlander Kluger · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. DISCHARGE FUEL SYSTEM PRESSURE

HINT:
Click here.


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE REAR CENTER SEAT ASSEMBLY

4. REMOVE REAR SEAT HEADREST ASSEMBLY (for LH Side)

5. REMOVE SEAT TRACK BRACKET COVER LH

  1. B173775
    Disengage the 8 claws and remove the 2 rear seat track bracket covers.


6. REMOVE REAR OUTER TRACK BRACKET COVER LH

  1. B173776
    Disengage the 4 claws and remove the rear outer track bracket cover.


7. REMOVE REAR INNER TRACK BRACKET COVER LH

  1. B173777
    Disengage the 4 claws and remove the rear inner track bracket cover.


8. REMOVE REAR SEAT LEG SIDE COVER LH

  1. B173779
    Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.


9. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY LH (w/ Remote Folding Function)

  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

    B180388E01

  1. B174594E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

    B173770E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    B180393E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.


10. REMOVE REAR NO. 1 SEAT ASSEMBLY LH

  1. B173780
    Remove the 3 bolts on the rear side of the seat.

  1. B173778
    Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


11. REMOVE REAR SEAT HEADREST ASSEMBLY (for RH Side)

12. REMOVE SEAT TRACK BRACKET COVER RH

  1. B173760
    Disengage the 8 claws and remove the 2 rear seat track bracket covers.


13. REMOVE REAR OUTER TRACK BRACKET COVER RH

  1. B173763
    Disengage the 4 claws and remove the rear outer track bracket cover.


14. REMOVE REAR INNER TRACK BRACKET COVER RH

  1. B173761
    Disengage the 4 claws and remove the rear inner track bracket cover.


15. REMOVE REAR SEAT LEG SIDE COVER RH

  1. B173765
    Disengage the 3 claws.

  1. Disengage the clip and remove the rear seat leg side cover.


16. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY RH (w/ Remote Folding Function)

  1. Pull down the adjuster's lock piece to release the lock as shown in the illustration.

    B180390E01

  1. B173766E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws as shown in the illustration.

  1. Lift up the seat track adjusting handle to the uppermost position and hold the handle in this position as shown in the illustration.

    B173768E01

  1. Using a screwdriver wrapped with protective tape, disconnect the rear No. 1 seat lock cable assembly as shown in the illustration.

  1. Using a screwdriver wrapped with protective tape, disconnect the rear seat reclining control cable as shown in the illustration.

    B180392E01

  1. Secure the rear seat reclining control cable with the carpet hole as shown in the illustration.


17. REMOVE REAR NO. 1 SEAT ASSEMBLY RH

  1. B173774
    Remove the 3 bolts on the rear side of the seat.

  1. B173764
    Remove the 2 bolts on the front side of the seat and the rear No. 1 seat assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


18. REMOVE REAR DOOR SCUFF PLATE LH

  1. B173228
    Disengage the 5 claws, 3 clips and guide, and remove the rear door scuff plate LH.


19. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

  1. B173232
    Remove the rear door opening trim weatherstrip LH.


20. REMOVE DECK BOARD ASSEMBLY

  1. B173240
    Remove the deck board assembly.


21. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY

  1. B173242
    Disengage the 2 guides and remove the No. 3 deck board sub-assembly.


22. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY

  1. B173244
    Disengage the 2 guides and remove the No. 2 deck board sub-assembly.


23. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

24. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat)

  1. B175152
    Disengage the 3 clips and the 3 guides, and remove the rear No. 1 floor board.


25. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat)

  1. B173607
    Disengage the 2 clips and remove the rear seat side cover LH.


26. REMOVE DECK SIDE TRIM BOX LH

  1. B173243E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box LH as shown in the illustration.

    B178554


27. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat)

  1. B173608
    Disengage the 2 clips and remove the rear seat side cover RH.


28. REMOVE JACK CARRIER SUPPORT

29. REMOVE JACK CARRIER CUSHION (for LHD)

  1. B178550
    Remove the jack carrier cushion.


30. REMOVE JACK CARRIER CUSHION (for RHD)

  1. B178551
    Remove the jack carrier cushion.


31. REMOVE JACK ASSEMBLY (for LHD)

  1. B173245
    Remove the jack assembly.


32. REMOVE JACK ASSEMBLY (for RHD)

  1. B178566
    Remove the jack assembly.


33. REMOVE JACK CARRIER ASSEMBLY (for LHD)

  1. B178548
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


34. REMOVE JACK CARRIER ASSEMBLY (for RHD)

  1. B179785
    Using a screwdriver, disengage the 3 claws and remove the jack carrier assembly.


35. REMOVE DECK SIDE TRIM BOX RH

  1. B173247E01
    Remove the 2 deck side trim clips and clip.

  1. Remove the deck side trim box RH as shown in the illustration.

    B178552


36. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat)

  1. B178560
    Remove the 4 bolts and 4 nuts.

  1. Remove the deck floor board assembly.


37. REMOVE REAR MAT

  1. B173249
    Remove the rear mat.


38. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat)

  1. B178561
    Disengage the 3 claws.

  1. Remove the 2 nuts and the deck floor board assembly.


39. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat)

  1. B173679
    Remove the 2 nuts and the deck floor box.


40. REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B170935
    Remove the bolt and rear No. 2 seat inner belt assembly.

    HINT:
    Use the same procedure for the RH side and LH side.


41. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY LH (w/ Rear No. 2 Seat)

  1. B170936
    Remove the bolt and disconnect the rear seat lap type belt assembly LH.


42. DISCONNECT REAR SEAT LAP TYPE BELT ASSEMBLY RH (w/ Rear No. 2 Seat)

HINT:
Use the same procedure for the RH side and the LH side.


43. REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)

  1. B173781
    Remove the 4 bolts and the rear No. 2 seat assembly.


44. REMOVE REAR FLOOR FINISH PLATE

  1. B173609
    Disengage the 4 clips and the 4 claws, and remove the rear floor finish plate.


45. REMOVE DECK SIDE TRIM COVER NO.2

  1. B173595E01
    Using a screwdriver, disengage the 2 claws and remove the deck side trim cover LH.

    HINT:
    Tape the screwdriver tip before use.


46. REMOVE DECK SIDE TRIM LH

  1. B173596
    Remove the bolt.

  1. B173623
    Disengage the 4 claws and the 3 guides, and remove the deck side trim LH as shown in the illustration.


47. REMOVE SIDE TRIM COVER LH

  1. B173597
    Disengage the 10 claws and remove the side trim cover LH.


48. REMOVE REAR COMBINATION LIGHT SERVICE COVER LH

  1. B173611E01
    Using a screwdriver, disengage the 6 claws and 2 guides, and remove the rear combination light service cover LH.

    HINT:
    Tape the screwdriver tip before use.


49. REMOVE REAR POWER POINT SOCKET ASSEMBLY
  1. Disconnect the connector.

  1. E151327
    Disengage the claw and remove the rear power point socket assembly.


50. REMOVE REAR POWER OUTLET SOCKET COVER

  1. E151328
    Disengage the 2 claws and remove the rear power outlet socket cover.


51. REMOVE REAR DECK TRIM COVER (w/o Remote Folding Function)

  1. B173602
    Disengage the 10 claws and remove the rear deck trim cover.


52. REMOVE RECLINING REMOTE CONTROL LEVER BEZEL LH (w/ Remote Folding Function)

  1. B173603
    Disengage the 5 claws and remove the reclining remote control bezel LH.


53. REMOVE ROPE HOOK ASSEMBLY (for LH Side)

  1. B173598E01
    for Front Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and the rope hook assembly.

  1. B173600E01
    for Rear Side:

    1. Using a screwdriver, disengage the 2 claws.

      HINT:
      Tape the screwdriver tip before use.

    2. Remove the bolt and rope hook assembly.


54. REMOVE NO. 2 DECK SIDE TRIM HOOK

  1. B173612
    Remove the screw and the No. 2 deck side trim hook.


55. REMOVE FRONT DECK SIDE TRIM COVER LH

  1. B173604E01
    Using a screwdriver, disengage the 4 claws and remove the 2 front deck side trim covers LH.

    HINT:
    Tape the screwdriver tip before use.


56. DISCONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

  1. B170933
    Remove the bolt and disconnect the floor end of the rear No. 1 seat outer belt assembly.


57. REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
  1. Remove the 2 bolts.

  1. Remove the 2 clips.

  1. Disengage the 7 claws and 4 clips, and remove the deck trim side panel assembly LH.

    B173613


58. REMOVE REAR FLOOR SERVICE HOLE COVER

  1. Lift up the front floor carpet.

    1. A171920
      Using a clip remover, remove the 3 clips and lift up the front floor carpet. (w/ rear No. 2 seat)

    2. A176884
      Disengage the 3 claws and lift up the front floor carpet. (w/o rear No. 2 seat)

  1. A171921
    Remove the rear floor service hole cover.

  1. Disconnect the fuel pump connector.


59. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

  1. A172549E01
    Remove the tube joint clip, and pull out the fuel pump tube.

    NOTICE:
    1. Check that there is no dirt or other foreign objects around the connector before disconnecting it. Clean the connector if necessary.
    2. It is necessary to prevent mud or dirt from entering the quick connector. If mud or dirt gets in the connector, the O-rings may not seal properly.
    3. Disconnect the quick connector by hand. Do not use any tools
    4. Do not bend, kink or twist the nylon tubes. Protect the connector by covering it with a plastic bag.
    5. If the pipe and connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off carefully.

  1. A171922E01
    Using a 6 mm socket hexagon wrench, install SST to the fuel pump gauge retainer.
    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    HINT:
    1. Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.
    2. Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).

  1. A171923
    Using SST, loosen the fuel pump gauge retainer.
    SST
    09808-14020   (09808-01410, 09808-01420, 09808-01430)

    NOTICE:
    1. Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
    2. Loosen the retainer by turning it counterclockwise while holding SST down. Do not allow the claw of the tank suction tube support to slip out of its groove on the fuel tank.

    HINT:
    The ribs on the fuel pump gauge retainer can be fitted into the tips of SST.

  1. Remove the fuel pump gauge retainer.

  1. A169370E01
    Remove the fuel suction tube with pump and gauge.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the fuel tank.


60. DRAIN FUEL

61. REMOVE FRONT CENTER FLOOR COVER

  1. C168088
    Remove the 4 bolts, 2 screws, and the nut.

  1. C168089
    Disengage the 4 clips and remove the center front floor cover.


62. REMOVE TAIL EXHAUST PIPE ASSEMBLY

  1. A170139
    Remove the 2 bolts and 2 compression springs.

  1. Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.

  1. Remove the gasket from the center exhaust pipe assembly.


63. REMOVE CENTER EXHAUST PIPE ASSEMBLY

  1. A170125
    Remove the 2 bolts and 2 compression springs.

  1. Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.

  1. Remove the gasket from the No. 3 exhaust pipe sub-assembly.


64. REMOVE NO. 4 EXHAUST PIPE SUPPORT BRACKET

  1. A173193
    Remove the 2 bolts, and then remove the No. 4 exhaust pipe support bracket.


65. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

  1. C166039
    Depress the brake pedal and hold it.

  1. Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.

    HINT:
    Put a piece of cloth or equivalent into the inside of the universal joint cover so that the boot does not touch the inside of the universal joint cover.

  1. C166040E01
    Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.

  1. Remove the 4 nuts, 4 bolts and 4 washers.

  1. C166041
    Remove the 4 bolts and 4 adjusting shims.

  1. C166073
    Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.

  1. C166042E01
    Insert SST into the transfer to prevent oil leakage.
    SST
    09325-20010  


66. REMOVE REAR WHEELS (for 4WD)

67. SEPARATE REAR SPEED SENSOR LH (for 4WD)

  1. C165809
    Remove the bolt and separate the rear speed sensor from the rear axle carrier sub-assembly.

    NOTICE:
    Keep the sensor tip and rear speed sensor installation hole free from foreign matter.


68. SEPARATE REAR SPEED SENSOR RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


69. REMOVE REAR AXLE SHAFT NUT LH (for 4WD)

  1. C165539E01
    Using SST and a hammer, release the staked part of the rear axle shaft nut.
    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the rear axle shaft nut.


70. REMOVE REAR AXLE SHAFT NUT RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


71. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY LH (for 4WD)

  1. C165996
    Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.


72. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


73. REMOVE REAR DISC (for 4WD LH Side)

  1. C166438E01
    Put matchmarks on the rear disc and the axle hub.

  1. D028126
    Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.


74. REMOVE REAR DISC (for 4WD RH Side)

75. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH (for 4WD)

  1. C166348E01
    Put matchmarks on the drive shaft and axle hub.

    NOTICE:
    Do not punch the marks.

  1. C165997
    Remove the 4 bolts and the rear axle hub and bearing assembly.

    NOTICE:
    1. Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.
    2. Use wire or an equivalent tool to keep the parking brake assembly from hanging down by the parking brake cable assembly.


76. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


77. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for 4WD)

  1. C165998
    Remove the bolt and the nut, and separate the No. 3 parking brake cable assembly.


78. REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for 4WD)

HINT:
Perform the same procedure as the No. 3 parking brake cable assembly.


79. REMOVE REAR STRUT ROD ASSEMBLY LH (for 4WD)

  1. C165999
    Remove the 2 bolts, the 2 nuts, and the rear strut rod assembly.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.


80. REMOVE REAR STRUT ROD ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


81. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY LH (for 4WD)

  1. C166000
    Loosen the 2 bolts.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.

  1. C166001
    Remove the 2 bolts and 2 nuts, and separate the rear shock absorber with coil spring (lower side) from the rear axle carrier sub-assembly.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.

  1. C166002
    Remove the 2 bolts, the 2 nuts, and the rear axle carrier sub-assembly.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.

    HINT:
    Use wire or an equivalent tool to keep the rear drive shaft assembly from hanging down.


82. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


83. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH (for 4WD)

C166222E01
  1. Put matchmarks on the adjust cams and the rear suspension member sub-assembly.

  1. Remove the nut, the No. 2 camber adjust cam, the rear suspension toe adjust cam sub-assembly, and the rear No. 2 suspension arm assembly LH.

    NOTICE:
    Mark the removed parts to distinguish left from right and keep them in order for reinstallation.

    HINT:
    When removing the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.


84. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


85. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH (for 4WD)

C166223
  1. Remove the bolt, the nut, and the rear No. 1 suspension arm assembly RH from the rear suspension member sub-assembly.

    NOTICE:
    1. Since a stopper nut is used, loosen the bolt.
    2. Mark the removed parts to distinguish left from right and keep them in order for reinstallation.


86. REMOVE REAR DIFFERENTIAL FILLER PLUG (for 4WD)

  1. C166706
    Using a hexagon wrench (10 mm), remove the rear differential filler plug and rear differential filler plug gasket.


87. REMOVE REAR DIFFERENTIAL DRAIN PLUG (for 4WD)

  1. C166707
    Using a hexagon wrench (10 mm), remove the rear differential drain plug and rear differential drain plug gasket, and drain the oil.


88. REMOVE REAR DRIVE SHAFT ASSEMBLY LH (for 4WD)

  1. C165540E01
    Using SST, remove the rear drive shaft assembly as shown in the illustration.
    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    Remove the rear drive shaft assembly while keeping it level.


89. REMOVE REAR DRIVE SHAFT SNAP RING LH (for 4WD)

  1. C057543E04
    Using a screwdriver, remove the rear drive shaft snap ring.


90. REMOVE REAR DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


91. REMOVE REAR DRIVE SHAFT SNAP RING RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


92. REMOVE REAR SUSPENSION MEMBER (for 4WD)

  1. C166232E01
    Support the rear suspension member with a jack using a wooden block.

    HINT:
    Use a properly sized wooden block to keep the jack and suspension member level.

  1. C166224E01
    Remove the 4 nuts, 2 bolts and 2 rear lower suspension member stopper retainers.

  1. Lower the rear suspension member.

  1. Remove the 2 rear upper suspension member stoppers.


93. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

  1. A173194E01
    Remove the 3 clips (A) and 7 nuts, and then remove the No. 1 fuel tank protector sub-assembly.


94. REMOVE FUEL TANK ASSEMBLY

  1. A173195E01
    Disconnect the fuel pump tube.

    1. Pinch the tab of the retainer to disengage the lock claws and pull it down as shown in the illustration.

    2. Pull out the fuel pump tube.

      NOTICE:
      1. Check if there is any dirt or mud around the connector before this operation and clean the connector if necessary.
      2. It is necessary to prevent mud or dirt from entering the quick connector. If any foreign objects enter the connector, the O-rings may seal properly.
      3. Do not use any tool in this operation.
      4. Do not bend or twist the nylon tube. Protect the connector by covering it with a plastic bag.
      5. When the pipe and connector are stuck, push and pull the connector to release it and pull the connector out carefully.

  1. A173196
    Disconnect the fuel tank vent hose.

    1. Slide the clamp and disconnect the fuel tank vent hose.

  1. A175984E02
    Disconnect the No. 3 fuel tank breather tube.

    1. Loosen the hose clamp bolt and disconnect the No. 3 fuel tank breather tube.

  1. A175985E02
    Loosen the hose clamp bolt and disconnect the fuel tank to filler pipe hose.

  1. Set a transmission jack under the fuel tank.

  1. Remove the 4 bolts, and then remove the 2 fuel tank bands.

  1. Remove the 2 nuts.

  1. Operate the transmission jack to remove the fuel tank.

    A173199


95. REMOVE REAR FUEL TANK SIDE PLATE

  1. A173200
    Remove the rear fuel tank side plate.


96. REMOVE NO. 1 FUEL TANK CUSHION

  1. A173201
    Remove the No. 1 fuel tank cushion.


97. REMOVE FUEL PUMP TUBE SUB-ASSEMBLY

  1. A173202E01
    Release the 2 claws, and then remove the fuel pump tube.


98. REMOVE FUEL TANK TO FILLER PIPE HOSE

  1. A173203
    Loosen the hose clamp bolt, and then remove the fuel tank to filler pipe hose.


99. REMOVE TANK SUCTION TUBE SUPPORT

  1. A173204
    Remove the tank suction tube support from the fuel tank.


100. REMOVE FUEL TANK SIDE PLATE

  1. A173205E01
    Remove the bolt and nut, and then remove the fuel tank side plate and the fuel tank bracket.


101. REMOVE FUEL TANK CUSHION SET

  1. A173206E01
    Remove the 2 fuel tank cushion sets and 2 No. 5 fuel tank cushions.

← COMPONENTS (from Jul 2010)REMOVAL (Aug 2008 – Jun 2010) →