2007-2013 Highlander Kluger · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE
(Click here)

2. DRAIN FUEL

3. REMOVE FRONT CENTER FLOOR COVER

  1. C168088
    Remove the 4 bolts, 2 screws, and the nut.

  1. C168089
    Disengage the 4 clips and remove the center front floor cover.


4. REMOVE TAIL EXHAUST PIPE ASSEMBLY

  1. A170139
    Remove the 2 bolts and 2 compression springs.

  1. Disconnect the exhaust pipe support and remove the tail exhaust pipe assembly.

  1. Remove the gasket from the center exhaust pipe assembly.


5. REMOVE CENTER EXHAUST PIPE ASSEMBLY

  1. A170125
    Remove the 2 bolts and 2 compression springs.

  1. Disconnect the 3 exhaust pipe supports and remove the center exhaust pipe assembly.

  1. Remove the gasket from the No. 3 exhaust pipe sub-assembly.


6. REMOVE NO. 4 EXHAUST PIPE SUPPORT BRACKET

  1. A173193
    Remove the 2 bolts, and then remove the No. 4 exhaust pipe support bracket.


7. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD)

  1. C166039
    Depress the brake pedal and hold it.

  1. Using a hexagon wrench (6 mm), loosen the cross groove joint set bolts 1/2 turn.

    HINT:
    Put a piece of cloth or equivalent into the inside of the universal joint cover so that the boot does not touch the inside of the universal joint cover.

  1. C166040E01
    Place matchmarks on the rear propeller shaft and rear drive pinion flange sub-assembly.

  1. Remove the 4 nuts, 4 bolts and 4 washers.

  1. C166041
    Remove the 4 bolts and 4 adjusting shims.

  1. C166073
    Using a brass bar and a hammer, remove the propeller shaft with center bearing shaft assembly.

  1. C166042E01
    Insert SST into the transfer to prevent oil leakage.
    SST
    09325-20010  


8. REMOVE REAR WHEELS (for 4WD)

9. SEPARATE REAR SPEED SENSOR LH (for 4WD)

  1. C165809
    Remove the bolt and separate the rear speed sensor from the rear axle carrier sub-assembly.

    NOTICE:
    Keep the sensor tip and rear speed sensor installation hole free from foreign matter.


10. SEPARATE REAR SPEED SENSOR RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


11. REMOVE REAR AXLE SHAFT NUT LH (for 4WD)

  1. C165539E01
    Using SST and a hammer, release the staked part of the rear axle shaft nut.
    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the rear axle shaft nut.


12. REMOVE REAR AXLE SHAFT NUT RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


13. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY LH (for 4WD)

  1. C165996
    Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.


14. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


15. REMOVE REAR DISC (for 4WD LH Side)

  1. C166438E01
    Put matchmarks on the rear disc and the axle hub.

  1. D028126
    Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.


16. REMOVE REAR DISC (for 4WD RH Side)

17. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH (for 4WD)

  1. C166348E01
    Put matchmarks on the drive shaft and axle hub.

    NOTICE:
    Do not punch the marks.

  1. C165997
    Remove the 4 bolts and the rear axle hub and bearing assembly.

    NOTICE:
    1. Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.
    2. Use wire or an equivalent tool to keep the parking brake assembly from hanging down by the parking brake cable assembly.


18. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


19. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for 4WD)

  1. C165998
    Remove the bolt and the nut, and separate the No. 3 parking brake cable assembly.


20. REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for 4WD)

HINT:
Perform the same procedure as the No. 3 parking brake cable assembly.


21. REMOVE REAR STRUT ROD ASSEMBLY LH (for 4WD)

  1. C165999
    Remove the 2 bolts, the 2 nuts, and the rear strut rod assembly.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.


22. REMOVE REAR STRUT ROD ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


23. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY LH (for 4WD)

  1. C166000
    Loosen the 2 bolts.

    NOTICE:
    Since stopper nuts are used, loosen the bolts.

  1. C166001
    Remove the 2 bolts and 2 nuts, and separate the rear shock absorber with coil spring (lower side) from the rear axle carrier sub-assembly.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.

  1. C166002
    Remove the 2 bolts, the 2 nuts, and the rear axle carrier sub-assembly.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.

    HINT:
    Use wire or an equivalent tool to keep the rear drive shaft assembly from hanging down.


24. REMOVE REAR AXLE CARRIER SUB-ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


25. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH (for 4WD)

C166222E01
  1. Put matchmarks on the adjust cams and the rear suspension member sub-assembly.

  1. Remove the nut, the No. 2 camber adjust cam, the rear suspension toe adjust cam sub-assembly, and the rear No. 2 suspension arm assembly LH.

    NOTICE:
    Mark the removed parts to distinguish left from right and keep them in order for reinstallation.

    HINT:
    When removing the nut, keep the rear suspension toe adjust cam sub-assembly from rotating.


26. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


27. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH (for 4WD)

C166223
  1. Remove the bolt, the nut, and the rear No. 1 suspension arm assembly RH from the rear suspension member sub-assembly.

    NOTICE:
    1. Since a stopper nut is used, loosen the bolt.
    2. Mark the removed parts to distinguish left from right and keep them in order for reinstallation.


28. REMOVE REAR DIFFERENTIAL FILLER PLUG (for 4WD)

  1. C166706
    Using a hexagon wrench (10 mm), remove the rear differential filler plug and rear differential filler plug gasket.


29. REMOVE REAR DIFFERENTIAL DRAIN PLUG (for 4WD)

  1. C166707
    Using a hexagon wrench (10 mm), remove the rear differential drain plug and rear differential drain plug gasket, and drain the oil.


30. REMOVE REAR DRIVE SHAFT ASSEMBLY LH (for 4WD)

  1. C165540E01
    Using SST, remove the rear drive shaft assembly as shown in the illustration.
    SST
    09520-01010  
    09520-24010   (09520-32040)

    NOTICE:
    Remove the rear drive shaft assembly while keeping it level.


31. REMOVE REAR DRIVE SHAFT SNAP RING LH (for 4WD)

  1. C057543E04
    Using a screwdriver, remove the rear drive shaft snap ring.


32. REMOVE REAR DRIVE SHAFT ASSEMBLY RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


33. REMOVE REAR DRIVE SHAFT SNAP RING RH (for 4WD)

HINT:
Perform the same procedure as the LH side.


34. REMOVE REAR SUSPENSION MEMBER (for 4WD)

  1. C166232E01
    Support the rear suspension member with a jack using a wooden block.

    HINT:
    Use a properly sized wooden block to keep the jack and suspension member level.

  1. C166224E01
    Remove the 4 nuts, 2 bolts and 2 rear lower suspension member stopper retainers.

  1. Lower the rear suspension member.

  1. Remove the 2 rear upper suspension member stoppers.


35. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

  1. A173194E01
    Remove the 3 clips (A) and 7 nuts, and then remove the No. 1 fuel tank protector sub-assembly.


36. REMOVE FUEL TANK ASSEMBLY

  1. A173195E01
    Disconnect the fuel pump tube.

    1. Pinch the tab of the retainer to disengage the lock claws and pull it down as shown in the illustration.

    2. Pull out the fuel pump tube.

      NOTICE:
      1. Check if there is any dirt or mud around the connector before this operation and clean the connector if necessary.
      2. It is necessary to prevent mud or dirt from entering the quick connector. If any foreign objects enter the connector, the O-rings may seal properly.
      3. Do not use any tool in this operation.
      4. Do not bend or twist the nylon tube. Protect the connector by covering it with a plastic bag.
      5. When the pipe and connector are stuck, push and pull the connector to release it and pull the connector out carefully.

  1. A173196
    Disconnect the fuel tank vent hose.

    1. Slide the clamp and disconnect the fuel tank vent hose.

  1. A175984E02
    Disconnect the No. 3 fuel tank breather tube.

    1. Loosen the hose clamp bolt and disconnect the No. 3 fuel tank breather tube.

  1. A175985E02
    Loosen the hose clamp bolt and disconnect the fuel tank to filler pipe hose.

  1. Set a transmission jack under the fuel tank.

  1. Remove the 4 bolts, and then remove the 2 fuel tank bands.

  1. Remove the 2 nuts.

  1. Operate the transmission jack to remove the fuel tank.

    A173199


37. REMOVE REAR FUEL TANK SIDE PLATE

  1. A173200
    Remove the rear fuel tank side plate.


38. REMOVE NO. 1 FUEL TANK CUSHION

  1. A173201
    Remove the No. 1 fuel tank cushion.


39. REMOVE FUEL PUMP TUBE SUB-ASSEMBLY

  1. A173202E01
    Release the 2 claws, and then remove the fuel pump tube.


40. REMOVE FUEL TANK TO FILLER PIPE HOSE

  1. A173203
    Loosen the hose clamp bolt, and then remove the fuel tank to filler pipe hose.


41. REMOVE TANK SUCTION TUBE SUPPORT

  1. A173204
    Remove the tank suction tube support from the fuel tank.


42. REMOVE FUEL TANK SIDE PLATE

  1. A173205E01
    Remove the bolt and nut, and then remove the fuel tank side plate and the fuel tank bracket.


43. REMOVE FUEL TANK CUSHION SET

  1. A173206E01
    Remove the 2 fuel tank cushion sets and 2 No. 5 fuel tank cushions.

← REMOVAL (Aug 2008 – Jun 2010)INSTALLATION (May 2007 – Jul 2008) →