2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


TELEVISION CAMERA ASSEMBLY

  1. Disconnect the S1 camera connector.
    E150739E03

  2. Measure the voltage of each terminal of the wire harness side connector.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S1-3 (CGND) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 V
    S1-4 (CB+) - S1-3 (CGND)
    B - W
    Power source
    Ignition switch on (IG)
    Shift lever R position
    Approx. 6 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the S1 camera connector.

  4. Measure the voltage and frequency of each terminal of the connector.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S1-1 (CV-) - S1-2 (CV+)
    BR - R
    Display signal
    Ignition switch on (IG)
    Shift lever R position
    Pulse generation
    (See waveform 1)
    If the result is not as specified, the camera may have a malfunction.

  5. E119731E01
    Reference:
    Oscilloscope waveform

    1. Waveform 1

      Item
      Content
      Measure terminal
      S1-1 (CV-) - S1-2 (CV+)
      Measure set
      0.2 V/DIV., 0.2 μS/DIV.
      Condition
      Ignition switch: on (IG), Shift lever: R position


CLOCK ASSEMBLY (Multi-Information Display)
E146933E03
Terminal No. (Symbols)
Wiring Color
Terminal Description
Condition
Specified Condition
E9-1 (IG) - E9-5 (GND)
P - W-B
Ignition switch signal
Ignition switch off
Below 1 V
Ignition switch on (IG)
11 to 14 V
E9-2 (REV) - E9-5 (GND)
R - W-B
Reverse signal
Ignition switch on (IG)
Shift lever except R position
Below 1 V
Ignition switch on (IG)
Shift lever R position
11 to 14 V
E9-4 (CGND) - E9-5 (GND)
W - W-B
Television camera ground
Always
Below 1 V
E9-5 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 V
E9-6 (+B) - E9-5 (GND)
Y - W-B
Battery
Always
11 to 14 V
E9-12 (CA+) - E9-5 (GND)
B - W-B
Power source to television camera
Ignition switch on (IG)
Shift lever R position
Approx. 6 V
E9-14 (V+) - E9-5 (GND)
R - W-B
Television camera display signal (Input)
Ignition switch on (IG)
Shift lever R position
Pulse generation
(See waveform 1)
E9-15 (V-) - E9-5 (GND)
Shielded - W-B
Television camera ground (Shielded)
Always
Below 1 V
E9-16 (SGND) - Body ground
BR - Body ground
Signal ground
Always
Below 1 V

  1. E119731E06
    Reference:
    Oscilloscope waveform

    1. Waveform 1

      Item
      Content
      Measure terminal
      E9-14 (V+) - E9-15 (V-)
      Measure set
      0.2 V/DIV., 0.2 μS/DIV.
      Condition
      Ignition switch: on (IG), Shift lever: R position

← PROBLEM SYMPTOMS TABLE (from Jul 2010)TERMINALS OF ECU (from Jul 2010) →