2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


TELEVISION CAMERA ASSEMBLY
E150739E19
  1. Disconnect the T16 connector from the television camera assembly.

  2. Measure the voltage of each terminal of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T16-3 (CGND) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 V
    T16-4 (CB+) - T16-3 (CGND)
    B - W
    Power source
    Ignition switch ON
    Shift lever in R
    5.5 to 7.05 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the T16 connector to the television camera assembly.

  4. Check for pulses between each terminal of the connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    T16-2 (CV+) - T16-1 (CV-)
    R - L
    Display signal
    Ignition switch ON
    Shift lever in R
    Camera lens not covered, displaying an image
    Pulse generation
    (See waveform 1)
    Ignition switch ON
    Shift lever in R
    Camera lens covered, blacking out screen
    Pulse generation
    (See waveform 2)

    HINT:
    A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.

    If the result is not as specified, the camera may have a malfunction.

  5. E171712E13
    Reference (Oscilloscope waveform):

    HINT:
    A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


    1. Waveform 1 (camera lens is not covered, displaying an image)

      Item
      Content
      Terminal No. (Symbol)
      T16-2 (CV+) - T16-1 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the television camera assembly.

    2. Waveform 2 (camera lens is covered, blacking out the screen)

      Item
      Content
      Terminal No. (Symbol)
      T16-2 (CV+) - T16-1 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the television camera assembly.

      Text in Illustration 
      *a
      Waveform 1 (camera lens not covered, displaying an image)
      *b
      Waveform 2 (camera lens covered, blacking out the screen)
      *c
      Synchronization Signal
      *d
      Video Waveform


CLOCK ASSEMBLY (Multi-Information Display)
E146933E10
  1. Disconnect the E9 connector from the clock assembly.

  2. Measure the voltage of each terminal of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E9-1 (IG) - Body ground
    P - Body ground
    Ignition switch signal
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V
    E9-2 (REV) - E9-5 (GND)
    R - W-B
    Reverse signal
    Ignition switch ON
    Shift lever in any position except R
    Below 1 V
    Ignition switch ON
    Shift lever in R
    11 to 14 V
    E9-4 (CGND) - E9-5 (GND)
    W - W-B
    Television camera ground
    Always
    Below 1 V
    E9-5 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 V
    E9-6 (+B) - Body ground
    Y - Body ground
    Battery
    Always
    11 to 14 V
    E9-12 (CA+) - E9-5 (GND)
    B - W-B
    Power source to television camera
    Ignition switch ON
    Shift lever in R
    5.5 to 7.05 V
    E9-15 (V-) - E9-5 (GND)
    Shielded - W-B
    Television camera ground (Shielded)
    Always
    Below 1 V
    E9-16 (SGND) - Body ground
    BR - Body ground
    Signal ground
    Always
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E9 connector to the clock assembly.

  4. Check for pulses between each terminal of the connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E9-14 (V+) - E9-5 (GND)
    R - W-B
    Display signal
    Ignition switch ON
    Shift lever in R
    Camera lens not covered, displaying an image
    Pulse generation
    (See waveform 1)
    Ignition switch ON
    Shift lever in R
    Camera lens covered, blacking out screen
    Pulse generation
    (See waveform 2)

    HINT:
    A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the clock assembly with the connector connected.

    If the result is not as specified, the camera may have a malfunction.

  5. E171712E13
    Reference (Oscilloscope waveform):

    HINT:
    A waterproof connector is used for the television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly with the connector connected.


    1. Waveform 1 (camera lens is not covered, displaying an image)

      Item
      Content
      Terminal No. (Symbol)
      E9-14 (V+) - E9-5 (GND)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the television camera assembly.

    2. Waveform 2 (camera lens is covered, blacking out the screen)

      Item
      Content
      Terminal No. (Symbol)
      E9-14 (V+) - E9-5 (GND)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Ignition switch ON, shift lever in R

      HINT:
      The video waveform changes according to the image sent by the television camera assembly.

      Text in Illustration 
      *a
      Waveform 1 (camera lens not covered, displaying an image)
      *b
      Waveform 2 (camera lens covered, blacking out the screen)
      *c
      Synchronization Signal
      *d
      Video Waveform

← TERMINALS OF ECU (May 2007 – Jun 2010)Reverse Signal Circuit (May 2007 – Jul 2008) →