TERMINALS OF ECU
System information · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010
| TELEVISION CAMERA ASSEMBLY |


Disconnect the S1 camera connector.
Measure the voltage between each terminal of the wire harness side connector.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbols)
Wiring Color
Terminal Description
Condition
Specified Condition
S1-3 (CGND) - Body ground
W - Body ground
Ground
Always
Below 1 V
S1-4 (CB+) - S1-3 (CGND)
B - W
Power source
Ignition switch on (IG), shift lever in reverse position
Approx. 6 V
Reconnect the S1 camera connector.
Measure the waveform between each terminal of the connector.
If the result is not as specified, the camera may have a malfunction.Terminal No. (Symbols)
Wiring Color
Terminal Description
Condition
Specified Condition
S1-1 (CV-) - S1-2 (CV+)
BR - R
Display signal
Ignition switch on (IG), shift lever in reverse position
Pulse generation
(See waveform 1)
Using an oscilloscope, check the waveform.

Waveform 1 (reference) Item
Content
Terminal No. (Symbols)
S1-1 (CV-) - S1-2 (CV+)
Tool
0.2 V/DIV., 0.2 μsec./DIV.
Condition
Ignition switch on (IG), shift lever in reverse position
| TELEVISION CAMERA ECU |


Disconnect the N16 ECU connector.
Measure the voltage between each terminal of the wire harness side connector.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbols)
Wiring Color
Terminal Description
Condition
Specified Condition
N16-1 (+B) - N16-8 (GND1)
V- W-B
Power source
Always
11 to 14 V
N16-3 (IG) - N16-8 (GND1)
L - W-B
IG signal input
Ignition switch on (IG)
11 to 14 V
N16-4 (ACC) - N16-8 (GND1)
Y - W-B
Accessory (ON)
Ignition switch off
Below 1 V
N16-4 (ACC) - N16-8 (GND1)
Y - W-B
Accessory (ON)
Ignition switch on (ACC)
11 to 14 V
N16-8 (GND1) - Body ground
W-B - Body ground
Ground
Always
Below 1 V
Reconnect the N16 ECU connector.
Measure the voltage and waveform between each terminal of the connector and body ground.
Terminal No. (Symbols)
Wiring Color
Terminal Description
Condition
Specified Condition
N15-19 (CV-) - N16-8 (GND1)
Shielded - W-B
Television camera ground (Shielded)
Always
Below 1 V
N15-20 (CV+) - N16-8 (GND1)
R - W-B
Television camera display signal input
Ignition switch on (IG), shift lever in reverse position
Pulse generation
(see waveform 1)
N15-28 (TX-) - N15-29 (TX+)
G - P
AVC-LAN communication signal
Ignition switch on (ACC)
2 to 3 V
N15-39 (CGND) - N16-8 (GND1)
W - W-B
Television camera ground
Always
Below 1 V
N15-40 (CB+) - N16-8 (GND1)
B - W-B
Power source to television camera
Ignition switch on (IG), shift lever in reverse position
Approx. 6 V
N15-6 (CANL) - Body ground
W - Body ground
CAN control bus
Always
Pulse generation
N15-7 (CANH) - Body ground
SB - Body ground
CAN control bus
Always
Pulse generation
N21-1 (GVO+) - N16-8 (GND1)
-
Digital image signal (Output)
Navigation or television camera display is on
Pulse generation
N21-2 (GVO-) - N16-8 (GND1)
-
Digital image signal (Output)
Navigation or television camera display is on
Pulse generation
N21-3 (GVG1) - Body ground
-
Ground
Always
Below 1 V
Using an oscilloscope, check the waveform.

Waveform 1 (reference) Item
Content
Terminal No. (Symbols)
N15-20 (CV+) - N15-19 (CV-)
Tool
0.2 V/DIV., 0.2 μsec./DIV.
Condition
Ignition switch on (IG), shift lever in reverse position
| NAVIGATION RECEIVER ASSEMBLY (Click here) |