2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010


TELEVISION CAMERA ASSEMBLY
E150739E02
  1. Disconnect the S1 camera connector.

  2. Measure the voltage between each terminal of the wire harness side connector.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S1-3 (CGND) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 V
    S1-4 (CB+) - S1-3 (CGND)
    B - W
    Power source
    Ignition switch on (IG), shift lever in reverse position
    Approx. 6 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the S1 camera connector.

  4. Measure the waveform between each terminal of the connector.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S1-1 (CV-) - S1-2 (CV+)
    BR - R
    Display signal
    Ignition switch on (IG), shift lever in reverse position
    Pulse generation
    (See waveform 1)
    If the result is not as specified, the camera may have a malfunction.

  5. E119731E01
    Using an oscilloscope, check the waveform.
    Waveform 1 (reference) 
    Item
    Content
    Terminal No. (Symbols)
    S1-1 (CV-) - S1-2 (CV+)
    Tool
    0.2 V/DIV., 0.2 μsec./DIV.
    Condition
    Ignition switch on (IG), shift lever in reverse position


TELEVISION CAMERA ECU
E125154E11
  1. Disconnect the N16 ECU connector.

  2. Measure the voltage between each terminal of the wire harness side connector.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    N16-1 (+B) - N16-8 (GND1)
    V- W-B
    Power source
    Always
    11 to 14 V
    N16-3 (IG) - N16-8 (GND1)
    L - W-B
    IG signal input
    Ignition switch on (IG)
    11 to 14 V
    N16-4 (ACC) - N16-8 (GND1)
    Y - W-B
    Accessory (ON)
    Ignition switch off
    Below 1 V
    N16-4 (ACC) - N16-8 (GND1)
    Y - W-B
    Accessory (ON)
    Ignition switch on (ACC)
    11 to 14 V
    N16-8 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the N16 ECU connector.

  4. Measure the voltage and waveform between each terminal of the connector and body ground.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    N15-19 (CV-) - N16-8 (GND1)
    Shielded - W-B
    Television camera ground (Shielded)
    Always
    Below 1 V
    N15-20 (CV+) - N16-8 (GND1)
    R - W-B
    Television camera display signal input
    Ignition switch on (IG), shift lever in reverse position
    Pulse generation
    (see waveform 1)
    N15-28 (TX-) - N15-29 (TX+)
    G - P
    AVC-LAN communication signal
    Ignition switch on (ACC)
    2 to 3 V
    N15-39 (CGND) - N16-8 (GND1)
    W - W-B
    Television camera ground
    Always
    Below 1 V
    N15-40 (CB+) - N16-8 (GND1)
    B - W-B
    Power source to television camera
    Ignition switch on (IG), shift lever in reverse position
    Approx. 6 V
    N15-6 (CANL) - Body ground
    W - Body ground
    CAN control bus
    Always
    Pulse generation
    N15-7 (CANH) - Body ground
    SB - Body ground
    CAN control bus
    Always
    Pulse generation
    N21-1 (GVO+) - N16-8 (GND1)
    -
    Digital image signal (Output)
    Navigation or television camera display is on
    Pulse generation
    N21-2 (GVO-) - N16-8 (GND1)
    -
    Digital image signal (Output)
    Navigation or television camera display is on
    Pulse generation
    N21-3 (GVG1) - Body ground
    -
    Ground
    Always
    Below 1 V

  5. E119731E01
    Using an oscilloscope, check the waveform.
    Waveform 1 (reference) 
    Item
    Content
    Terminal No. (Symbols)
    N15-20 (CV+) - N15-19 (CV-)
    Tool
    0.2 V/DIV., 0.2 μsec./DIV.
    Condition
    Ignition switch on (IG), shift lever in reverse position


NAVIGATION RECEIVER ASSEMBLY (Click here)
← TERMINALS OF ECU (May 2007 – Jul 2008)DTC CHECK / CLEAR (May 2007 – Jul 2008) →