2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

01-DD Master Reset

Diagnostic trouble codes · Vehicles built from Jul 2010

Also covers:

DESCRIPTION

DTC No.
DTC Detection Condition
Trouble Area
01-DD
*1
The device that should be the master has been disconnected after the engine starts.
  1. Radio receiver power source circuit
  2. AVC-LAN circuit between the radio receiver and component which has stored this code
  3. Radio receiver
  4. Component which has stored this code
01-E1
*2
The AMP device determines that the AMP output does not function even while the source device operates.

HINT:
*1: If the ignition switch is turned off after idling for 60 seconds, this DTC may be stored when the engine is started again (key type ignition switch only).
*2: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.

NOTICE:
  1. Before starting troubleshooting, be sure to clear the DTCs stored due to the reasons described in the Hint above. Then, check for DTCs and troubleshoot according to the output DTCs.
  2. The radio receiver is the master unit.
  3. Be sure to clear and recheck for DTCs after the inspection is completed to confirm that no DTCs are output.


INSPECTION PROCEDURE

NOTICE:
Be sure to read Description before performing the following procedure.


1. CHECK RADIO RECEIVER POWER SOURCE CIRCUIT

HINT:
Refer to Radio Receiver Power Source Circuit (Click here).

If the power source circuit is operating normally, proceed to the next step.

NEXT


2. INSPECT RADIO RECEIVER

  1. E200688E20
    Disconnect the radio receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E24-9 (TXM+) - E24-10 (TXM-)
    Always
    60 to 80 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Radio Receiver)



NG
REPLACE RADIO RECEIVER (Click here)
OK


3. IDENTIFY COMPONENT WHICH HAS STORED THIS CODE

  1. Enter diagnostic mode.E110915E13

  1. Press preset switch "2" to change the mode to "Detailed Information Mode".

  1. Identify the component which has stored this code.

    Component Table 
    Component
    Physical Address
    Multi-media interface ECU
    388

    HINT:
    1. The physical address "P440" shown in the above example indicates the stereo component amplifier.
    2. For details of the DTC display, refer to DTC Check/Clear (Click here).


NEXT


4. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - COMPONENT WHICH HAS STORED THIS CODE)

HINT:
For details of the connectors, refer to Terminals of ECU (Click here).

  1. Referring to the following AVC-LAN wiring diagram, check the AVC-LAN circuit between the radio receiver and component which has stored this code.

    1. Disconnect all connectors between the radio receiver and component which has stored this code.

    2. Check for an open or short in the AVC-LAN circuit between the radio receiver and component which has stored this code.

      OK:
      There is no open or short circuit.

      E162966E13



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE RADIO RECEIVER
  1. Replace the radio receiver with a known good one.


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. RECHECK FOR DTC
  1. Recheck for DTCs and check if the same DTC is output again.

    OK:
    No DTCs are output.



NG
REPLACE COMPONENT WHICH HAS STORED THIS CODE
OK

END


← 01-DC Transmission Error (from Jul 2010)01-DF Master Error (from Jul 2010) →