2007-2013 Highlander Kluger · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from May 2007


1. REMOVE FRONT DIFFERENTIAL RING GEAR

  1. C050182E03
    Place matchmarks on the ring gear and differential case.

  1. C050183E02
    Remove the 16 bolts.

  1. C050184E02
    Using a plastic hammer, tap the ring gear to remove it from the case.


2. REMOVE FRONT DIFFERENTIAL SIDE GEAR

  1. C050187E02
    Remove the differential LH case from the differential case assembly.

  1. C050188E04
    Remove the No. 2 differential case from the differential case LH.

  1. D101210E03
    Remove the front differential side gear, front differential side gear thrust washer, conical spring, and No. 2 center differential side gear thrust washer from the differential case LH.

  1. D025610E01
    Using a snap ring expander, remove the pinion shaft spacer snap ring.

  1. C050190E01
    Using a pin punch and hammer, remove the 3 straight pins.

  1. C050191E01
    Remove the center differential pinion shaft and 2 differential pinion shafts.

  1. C050943E01
    Remove the 4 front differential pinions, 4 front differential pinion thrust washers, front differential pinion shaft holder, front differential side gear, and front differential side gear thrust washer.


3. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

  1. D025597E05
    Using SST, remove the front differential case rear tapered roller bearing from the differential case.
    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00480)

  1. D025598E03
    Using SST, remove the front differential case rear tapered roller bearing outer race and differential case washer.
    SST
    09308-00010  

    NOTICE:
    1. When replacing the bearing, be sure to replace both outer and inner races.
    2. When replacing the bearing, be sure to replace both left and right bearings as a set.


4. REMOVE CENTER DIFFERENTIAL PINION

  1. C050193E01
    Using a "TORX" socket (T50), remove the 15 bolts.

  1. C050230E02
    Place matchmarks on the differential intermediate case and differential case.

  1. Remove the differential intermediate case from the differential case RH.

  1. C050196E02
    Remove the center differential side gear, conical spring washer, and No. 1 center differential side gear thrust washer RH from the differential case RH.

  1. C050194E01
    Remove the differential spider, 5 center differential pinions, and 5 center differential pinion thrust washers from the differential intermediate case.


5. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

  1. D025611E01
    Using SST, remove the front differential case front tapered roller bearing from the differential case.
    SST
    09950-00020  
    09950-00030  
    SST
    09950-60010   (09951-00600)

  1. D025596E03
    Using SST, remove the front differential case front tapered roller bearing outer race and differential case washer.
    SST
    09308-00010  


6. REMOVE TRANSAXLE HOUSING OIL SEAL

  1. D025599E02
    Using SST, remove the oil seal.
    SST
    09950-70010   (09951-07100)
    SST
    09649-17010  


7. REMOVE DIFFERENTIAL SIDE BEARING RETAINER OIL SEAL

  1. D025600E02
    Using SST, remove the oil seal.
    SST
    09950-70010   (09951-07100)
    09608-10010  

← COMPONENTS (from May 2007)INSPECTION (from May 2007) →