2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Headlight (HI-BEAM) Circuit

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The main body ECU receives a signal from the headlight dimmer switch assembly to control the HI-beam headlights.

WIRING DIAGRAM

E142682E02

INSPECTION PROCEDURE


1. CHECK HEADLIGHT
  1. Check the operation of LO-beam headlights.

    OK:
    LO-beam headlights operate normally.



NG
GO TO PROBLEM SYMPTOMS TABLE (Click here)
OK


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Turn the intelligent tester on.

  1. Select the following menu items: Body Electrical / Main Body / Active Test.

  1. Check that the relay operates.

    Main Body: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Head Light (HI)
    HI-beam headlight relay
    ON / OFF
    -

    OK:
    Relay operates. (HI-beam headlights illuminate.)



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

3. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY

  1. E121532E04
    Remove the H-LP (RH) fuse and H-LP (LH) fuse from the engine room junction block assembly.

  1. Measure the voltage between the loading slot of each fuse and body ground.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    H-LP (RH) terminal - Body ground
    Light control switch in HEAD and dimmer switch in HIGH
    11 to 14 V
    H-LP (LH) terminal - Body ground
    Light control switch in HEAD and dimmer switch in HIGH
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUSE - BODY GROUND)
OK


4. INSPECT ENGINE ROOM JUNCTION BLOCK ASSEMBLY

  1. A137364E17
    Remove the engine room junction block assembly from the engine room relay block.

  1. Connect the positive (+) lead from the battery to terminal 2G-1.

  1. Connect the negative (-) lead from the battery to terminal 2D-8, 2D-9 and 2E-11.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    2B-2 - Battery negative
    Always
    11 to 14 V
    2B-3 - Battery negative
    Always
    11 to 14 V



NG
REPLACE ENGINE ROOM JUNCTION BLOCK ASSEMBLY
OK


5. CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK ASSEMBLY - MAIN BODY ECU)

  1. E151679E01
    Disconnect the 2D and 2E engine room junction block assembly connectors.

  1. Disconnect the 1D instrument panel junction block connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    2E-11 - 1D-9
    Always
    Below 1 Ω
    2D-9 - 1D-3
    Always
    Below 1 Ω
    2E-11 - Body ground
    Always
    10 kΩ or higher
    2D-9 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← Headlight Relay Circuit (from Jul 2010)Headlight (HI-BEAM) Circuit (Aug 2008 – Jun 2010) →