INSPECTION
Inspection · Vehicles built from May 2007
| INSPECT PACK CLEARANCE OF REVERSE CLUTCH |
Install the intermediate shaft and needle roller bearing onto the transaxle rear cover.

Using a dial indicator, measure the reverse clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
- Pack clearance:
- 0.60 to 0.82 mm (0.0236 to 0.0323 in.)
| INSPECT PACK CLEARANCE OF DIRECT CLUTCH AND OVERDRIVE CLUTCH |
Using a dial indicator, measure the direct clutch and overdrive clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

- Pack clearance:
- 0.61 to 0.83 mm (0.0240 to 0.0327 in.)
| INSPECT DIRECT MULTIPLE CLUTCH DISC |
Check if the sliding surfaces of the disc, plate, and flange are worn or burnt.

If necessary, replace them.- HINT:
- If the lining of the disc comes off or discolors, or if a part of the groove is worn, replace all discs.
- Before installing new discs, immerse them in ATF for at least 15 minutes.
- If the lining of the disc comes off or discolors, or if a part of the groove is worn, replace all discs.
| INSPECT OVERDRIVE DIRECT CLUTCH DISC |
Check if the sliding surface of the disc, plate, and flange are worn or burnt.

If necessary, replace them.- HINT:
- If the lining of the disc comes off or discolors, or if a part of the groove is worn, replace all discs.
- Before installing new discs, immerse them in ATF for at least 15 minutes.
- If the lining of the disc comes off or discolors, or if a part of the groove is worn, replace all discs.
| INSPECT OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY |
Using vernier calipers, measure the free length of the spring together with the spring seat.

- Standard free length:
- 25.91 mm (1.0201 in.)
| INSPECT PACK CLEARANCE OF REVERSE CLUTCH |
Install the intermediate shaft onto the transaxle rear cover.

Using a dial indicator, measure the direct clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
- Clearance:
- 0.60 to 0.82 mm (0.0236 to 0.0323 in.)
- HINT:
- There are 7 different thicknesses of flanges available.
Flange thickness: mm (in.) No.
Thickness
No.
Thickness
1
3.0 (0.118)
5
3.4 (0.134)
2
3.1 (0.122)
6
3.5 (0.138)
3
3.2 (0.126)
7
3.6 (0.142)
4
3.3 (0.130)
-
-
| INSPECT PACK CLEARANCE OF DIRECT CLUTCH AND OVERDRIVE CLUTCH |
Using a dial indicator, measure the direct clutch and overdrive clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
- Clearance:
- 0.61 to 0.83 mm (0.0240 to 0.0323 in.)
- HINT:
- There are 7 different thicknesses of flanges available.
Flange thickness: mm (in.) No.
Thickness
No.
Thickness
0
2.5 (0.098)
4
2.9 (0.114)
1
2.6 (0.102)
5
3.0 (0.118)
2
2.7 (0.106)
6
3.1 (0.122)
3
2.8 (0.110)
-
-
Check that the disc rotates when rotating the disc after inserting the rear planetary sun gear.

- NOTICE:
- Do not place the rear planetary sun gear in a vise.
