2007-2013 Highlander Kluger · Service Manual HEATER & AIR CONDITIONING SYSTEM

B1421/21 Solar Sensor Circuit (Passenger Side)

Diagnostic trouble codes · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

E107008E01
The solar sensor, which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning AUTO mode. The output voltage from the solar sensor varies in accordance with the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning amplifier detects changes in the output voltage from the solar sensor.
DTC No.
DTC Detection Condition
Trouble Area
B1421/21
Open or short in passenger side solar sensor circuit
  1. Solar sensor
  2. Wire harness between solar sensor and air conditioning amplifier
  3. Wire harness between solar sensor and main body ECU
  4. Air conditioning amplifier

WIRING DIAGRAM

E152698E06

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (SOLAR SENS-P)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the intelligent tester main switch on.

  1. Select the item below in the Data List, and read the value displayed on the intelligent tester.

    Data List / Air Conditioner: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Solar Sens-P
    Passenger side solar sensor /
    Min.: 0, Max.: 255
    Passenger side solar sensor value increases as brightness increases
    -

    OK:
    The display is as specified in the normal condition column.


    Result:
    Result
    Proceed to
    NG
    A
    OK (Checking from PROBLEM SYMPTOMS TABLE)
    B
    OK (Checking from DTC)
    C



B
PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

C
REPLACE AIR CONDITIONING AMPLIFIER (Click here)
A


2. CHECK SOLAR SENSOR (SENSOR POWER INPUT)

  1. E152686E02
    Disconnect the F1 solar sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F1-6 (CLTB) - F1-3 (CLTE)
    Ignition switch off
    Below 1 V
    F1-6 (CLTB) - F1-3 (CLTE)
    Ignition switch on (IG)
    11 to 14 V



OK
Go to step 4
NG


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR)

  1. E152676E14
    Disconnect the D6 main body ECU connector.

  1. Disconnect the F1 solar sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D6-20 (CLTB) - F1-6 (CLTB)
    Always
    Below 1 Ω
    D6-18 (CLTE) - F1-3 (CLTE)
    Always
    Below 1 Ω
    D-20 (CLTB) - Body ground
    Always
    10 kΩ or higher
    D6-18 (CLTE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

4. CHECK SOLAR SENSOR

  1. E109215E38
    Remove the solar sensor (Click here) with its connector still connected.

  1. Connect the battery's positive (+) lead to terminal 6 (CLTB) and the negative (-) lead to terminal 3 (CLTE) of the solar sensor.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    F1-2 (TSR) - F1-3 (CLTE)
    Sensor is subjected to electric light
    0.8 to 4.3 V
    F1-2 (TSR) - F1-3 (CLTE)
    Sensor is covered with a cloth
    Below 0.8 V

    NOTICE:
    1. The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 6 and positive (+) lead to terminal 3 of the solar sensor.
    2. While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.

    HINT:
    1. Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor.
    2. As the inspection light is moved away from the sensor, the voltage decreases.



NG
REPLACE SOLAR SENSOR (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - AIR CONDITIONING AMPLIFIER)

  1. E152677E07
    Disconnect the F1 solar sensor connector.

  1. Disconnect the D37 air conditioning amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D373-32 (TSP) - F1-2 (TSR)
    Always
    Below 1 Ω
    D33-32 (TSP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)


← B1421/21 Solar Sensor Circuit (Passenger Side) (May 2007 – Jul 2008)B1421/21 Solar Sensor Circuit (Passenger Side) (from Jul 2010) →