B1421/21 Solar Sensor Circuit (Passenger Side)
Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION


The solar sensor, which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning AUTO mode. The output voltage from the solar sensor varies in accordance with the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning amplifier detects changes in the output voltage from the solar sensor.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1421/21 |
Open or short in passenger side solar sensor circuit |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (SOLAR SENS-P) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG) and turn the intelligent tester main switch on.
Select the item below in the Data List, and read the value displayed on the intelligent tester.
Data List / Air Conditioner: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Solar Sens-P
Passenger side solar sensor /
Min.: 0, Max.: 255
Passenger side solar sensor value increases as brightness increases
-
- OK:
- The display is as specified in the normal condition column.
- Result:
Result
Proceed to
NG
A
OK (Checking from PROBLEM SYMPTOMS TABLE)
B
OK (Checking from DTC)
C
|
|
||||
|
|
||||
| A | |
| 2. CHECK SOLAR SENSOR (SENSOR POWER INPUT) |
Disconnect the F1 solar sensor connector.

Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
F1-6 (CLTB) - F1-3 (CLTE)
Ignition switch off
Below 1 V
F1-6 (CLTB) - F1-3 (CLTE)
Ignition switch on (IG)
11 to 14 V
|
|
||||
| NG | |
| 3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR) |
Disconnect the D6 main body ECU connector.

Disconnect the F1 solar sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D6-20 (CLTB) - F1-6 (CLTB)
Always
Below 1 Ω
D6-18 (CLTE) - F1-3 (CLTE)
Always
Below 1 Ω
D-20 (CLTB) - Body ground
Always
10 kΩ or higher
D6-18 (CLTE) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 4. CHECK SOLAR SENSOR |
Remove the solar sensor (Click here) with its connector still connected.

Connect the battery's positive (+) lead to terminal 6 (CLTB) and the negative (-) lead to terminal 3 (CLTE) of the solar sensor.
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
F1-2 (TSR) - F1-3 (CLTE)
Sensor is subjected to electric light
0.8 to 4.3 V
F1-2 (TSR) - F1-3 (CLTE)
Sensor is covered with a cloth
Below 0.8 V
- NOTICE:
- The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 6 and positive (+) lead to terminal 3 of the solar sensor.
- While using the battery during inspection, do not bring the positive and negative tester probes too close to each other as a short circuit may occur.
- The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the negative (-) lead to terminal 6 and positive (+) lead to terminal 3 of the solar sensor.
- HINT:
- Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor.
- As the inspection light is moved away from the sensor, the voltage decreases.
- Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - AIR CONDITIONING AMPLIFIER) |
Disconnect the F1 solar sensor connector.

Disconnect the D37 air conditioning amplifier connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
D373-32 (TSP) - F1-2 (TSR)
Always
Below 1 Ω
D33-32 (TSP) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
