2007-2013 Highlander Kluger · Service Manual SECURITIES

TERMINALS OF ECU

System information · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


CHECK TRANSPONDER KEY AMPLIFIER

  1. Disconnect the D24 transponder key amplifier connector and measure the resistance according to the value(s) in the table below.
    B065593E40

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D24-7 (AGND) - Body ground
    G - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the D24 transponder key amplifier connector and measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D24-1 (VC5) - D24-7 (AGND)
    P - G
    Power source
    No key is in ignition key cylinder
    Below 1 V
    D24-1 (VC5) - D24-7 (AGND)
    P - G
    Power source
    Key is in ignition key cylinder
    4.6 to 5.4 V
    D24-4 (CODE) - D24-7 (AGND)
    R - G
    Demodulated signal of key code data
    No key is in ignition key cylinder
    Below 1 V
    D24-4 (CODE) - D24-7 (AGND)
    R - G
    Demodulated signal of key code data
    Key is in ignition key cylinder
    Waveform 1
    D24-5 (TXCT) - D24-7 (AGND)
    SB - G
    Key code output signal
    No key is in ignition key cylinder
    Below 1 V
    D24-5 (TXCT) - D24-7 (AGND)
    SB - G
    Key code output signal
    Key is in ignition key cylinder
    Waveform 2
    If the result is not as specified, the transponder key amplifier may have a malfunction.

  3. Inspect using an oscilloscope.

    1. B139208E01
      Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D24-4 (CODE) - D24-7 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key is in ignition key cylinder

    2. B139205E01
      Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D24-5 (TXCT) - D24-7 (AGND)
      Tool Setting
      2 V/DIV., 10 ms./DIV.
      Condition
      Key is in ignition key cylinder


CHECK TRANSPONDER KEY ECU ASSEMBLY

  1. Disconnect the D37 transponder key ECU connector and measure the resistance and voltage according to the value(s) in the table below.
    B088367E14

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D37-1 (+B) - D37-16 (GND)
    GR - V
    Battery
    Always
    11 to 14 V
    D37-2 (IG) - D37-16 (GND)
    P - V
    Ignition switch signal
    Ignition switch OFF
    Below 1 V
    D37-2 (IG) - D37-16 (GND)
    P - V
    Ignition switch signal
    Ignition switch ON
    11 to 14 V
    D37-3 (KSW) - D37-16 (GND)
    O - V
    Unlock warning switch signal
    No key is in ignition key cylinder
    10 kΩ or higher
    D37-3 (KSW) - D37-16 (GND)
    O - V
    Unlock warning switch signal
    Key is in ignition key cylinder
    Below 1 Ω
    D37-16 (GND) - Body ground
    V - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the D37 transponder key ECU connector and measure the resistance and voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D37-3 (KSW) - D37-16 (GND)
    O - V
    Unlock warning switch signal
    No key is in ignition key cylinder
    11 to 14 V
    D37-3 (KSW) - D37-16 (GND)
    O - V
    Unlock warning switch signal
    Key is in ignition key cylinder
    Below 1 V
    D37-4 (TXCT) - D37-5 (AGND)
    SB - G
    Transponder key amplifier communication signal
    No key is in ignition key cylinder
    Below 1 V
    D37-4 (TXCT) - D37-5 (AGND)
    SB - G
    Transponder key amplifier communication signal
    Key is in ignition key cylinder
    Waveform 1
    D37-5 (AGND) - Body ground
    G - Body ground
    Ground
    Always
    Below 1 Ω
    D37-7 (CTY) - D37-16 (GND)
    LG - V
    Door courtesy signal
    Switch pushed
    11 to 14 V
    D37-7 (CTY) - D37-16 (GND)
    LG - V
    Door courtesy signal
    Switch free
    Below 1 V
    D37-8 (IND) - D37-16 (GND)
    Y - V
    Security indicator light signal
    Security indicator light is on
    11 to 14 V
    D37-8 (IND) - D37-16 (GND)
    Y - V
    Security indicator light signal
    Security indicator light is off
    Below 1 V
    D37-9 (D) - D37-16 (GND)
    B - V
    Diagnostic tester communication
    Without communication
    Below 1 V
    D37-9 (D) - D37-16 (GND)
    B - V
    Diagnostic tester communication
    During communication
    Pulse generation
    D37-12 (EFII) - D37-16 (GND)
    BR - V
    ECM input signal
    Ignition switch OFF
    11 to 14 V
    D37-12 (EFII) - D37-16 (GND)
    BR - V
    ECM input signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
    Waveform 2
    D37-13 (EFIO) - D37-16 (GND)
    L - V
    ECM output signal
    Ignition switch OFF
    Below 1 V
    D37-13 (EFIO) - D37-16 (GND)
    L - V
    ECM output signal
    Ignition switch ON
    Waveform 3
    D37-14 (VC5) - D37-5 (AGND)
    P - G
    Power source
    No key is in ignition key cylinder
    Below 1 V
    D37-14 (VC5) - D37-5 (AGND)
    P - G
    Power source
    Key is in ignition key cylinder
    4.6 to 5.4 V
    D37-15 (CODE) - D37-5 (AGND)
    R - G
    Transponder key amplifier communication signal
    No key is in ignition key cylinder
    Below 1 V
    D37-15 (CODE) - D37-5 (AGND)
    R - G
    Transponder key amplifier communication signal
    Key is in ignition key cylinder
    Waveform 4
    If the result is not as specified, the transponder key ECU may have a malfunction.

  3. Inspect using an oscilloscope.

    1. B139205E01
      Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D37-4 (TXCT) - D37-5 (AGND)
      Tool Setting
      2 V/DIV., 10 ms./DIV.
      Condition
      Key is in ignition key cylinder

    2. B229710E01
      Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D37-12 (EFII) - D37-16 (GND)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.

    3. B139206E01
      Waveform 3 (Reference)
      Item
      Content
      Tester Connection
      D37-13 (EFIO) - D37-16 (GND)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON

    4. B139208E01
      Waveform 4 (Reference)
      Item
      Content
      Tester Connection
      D37-15 (CODE) - D37-5 (AGND)
      Tool Setting
      2 V/DIV., 20 ms./DIV.
      Condition
      Key is in ignition key cylinder


CHECK ECM

  1. Disconnect the B3 ECM connector and measure the resistance according to the value(s) in the table below.
    B171355E02

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    B3-1 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  2. Reconnect the B3 ECM connector. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D32-15 (IMO) - B3-1 (E1)
    BR - W-B
    Transponder key ECU output signal
    Ignition switch OFF
    11 to 14 V
    D32-15 (IMO) - B3-1 (E1)
    BR - W-B
    Transponder key ECU output signal
    Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
    Waveform 1
    D32-16 (IMI) - B3-1 (E1)
    L - W-B
    Transponder key ECU input signal
    Ignition switch OFF
    Below 1 V
    D32-16 (IMI) - B3-1 (E1)
    L - W-B
    Transponder key ECU input signal
    Ignition switch ON
    Waveform 2
    If the result is not as specified, the ECM may have a malfunction.

  3. Inspect using an oscilloscope.

    1. B229710E01
      Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D32-15 (IMO) - B3-1 (E1)
      Tool Setting
      5 V/DIV., 500 ms./DIV.
      Condition
      Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.

    2. B139206E01
      Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D32-16 (IMI) - B3-1 (E1)
      Tool Setting
      2 V/DIV., 1 s./DIV.
      Condition
      Ignition switch ON

← PROBLEM SYMPTOMS TABLE (from Jul 2010)TERMINALS OF ECU (from Jul 2010) →