TERMINALS OF ECU
System information · Vehicles built from Jul 2010
Versions by build date: May 2007 – Jun 2010 from Jul 2010
| CHECK TRANSPONDER KEY AMPLIFIER |
Disconnect the D24 transponder key amplifier connector and measure the resistance according to the value(s) in the table below.


If the result is not as specified, there may be a malfunction on the wire harness side.Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D24-7 (AGND) - Body ground
G - Body ground
Ground
Always
Below 1 Ω
Reconnect the D24 transponder key amplifier connector and measure the voltage according to the value(s) in the table below.
If the result is not as specified, the transponder key amplifier may have a malfunction.Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D24-1 (VC5) - D24-7 (AGND)
P - G
Power source
No key is in ignition key cylinder
Below 1 V
D24-1 (VC5) - D24-7 (AGND)
P - G
Power source
Key is in ignition key cylinder
4.6 to 5.4 V
D24-4 (CODE) - D24-7 (AGND)
R - G
Demodulated signal of key code data
No key is in ignition key cylinder
Below 1 V
D24-4 (CODE) - D24-7 (AGND)
R - G
Demodulated signal of key code data
Key is in ignition key cylinder
Waveform 1
D24-5 (TXCT) - D24-7 (AGND)
SB - G
Key code output signal
No key is in ignition key cylinder
Below 1 V
D24-5 (TXCT) - D24-7 (AGND)
SB - G
Key code output signal
Key is in ignition key cylinder
Waveform 2
Inspect using an oscilloscope.
Waveform 1 (Reference)

Item
Content
Tester Connection
D24-4 (CODE) - D24-7 (AGND)
Tool Setting
2 V/DIV., 20 ms./DIV.
Condition
Key is in ignition key cylinder
Waveform 2 (Reference)

Item
Content
Tester Connection
D24-5 (TXCT) - D24-7 (AGND)
Tool Setting
2 V/DIV., 10 ms./DIV.
Condition
Key is in ignition key cylinder
| CHECK TRANSPONDER KEY ECU ASSEMBLY |
Disconnect the D37 transponder key ECU connector and measure the resistance and voltage according to the value(s) in the table below.


If the result is not as specified, there may be a malfunction on the wire harness side.Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D37-1 (+B) - D37-16 (GND)
GR - V
Battery
Always
11 to 14 V
D37-2 (IG) - D37-16 (GND)
P - V
Ignition switch signal
Ignition switch OFF
Below 1 V
D37-2 (IG) - D37-16 (GND)
P - V
Ignition switch signal
Ignition switch ON
11 to 14 V
D37-3 (KSW) - D37-16 (GND)
BE - V
Unlock warning switch signal
No key is in ignition key cylinder
10 kΩ or higher
D37-3 (KSW) - D37-16 (GND)
BE - V
Unlock warning switch signal
Key is in ignition key cylinder
Below 1 Ω
D37-16 (GND) - Body ground
V - Body ground
Ground
Always
Below 1 Ω
Reconnect the D37 transponder key ECU connector and measure the resistance and voltage according to the value(s) in the table below.
If the result is not as specified, the transponder key ECU may have a malfunction.Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D37-3 (KSW) - D37-16 (GND)
BE - V
Unlock warning switch signal
No key is in ignition key cylinder
11 to 14 V
D37-3 (KSW) - D37-16 (GND)
BE - V
Unlock warning switch signal
Key is in ignition key cylinder
Below 1 V
D37-4 (TXCT) - D37-5 (AGND)
SB - G
Transponder key amplifier communication signal
No key is in ignition key cylinder
Below 1 V
D37-4 (TXCT) - D37-5 (AGND)
SB - G
Transponder key amplifier communication signal
Key is in ignition key cylinder
Waveform 1
D37-5 (AGND) - Body ground
G - Body ground
Ground
Always
Below 1 Ω
D37-7 (CTY) - D37-16 (GND)
LG - V
Door courtesy signal
Switch pushed
11 to 14 V
D37-7 (CTY) - D37-16 (GND)
LG - V
Door courtesy signal
Switch free
Below 1 V
D37-8 (IND) - D37-16 (GND)
Y - V
Security indicator light signal
Security indicator light is on
11 to 14 V
D37-8 (IND) - D37-16 (GND)
Y - V
Security indicator light signal
Security indicator light is off
Below 1 V
D37-9 (D) - D37-16 (GND)
B - V
Diagnostic tester communication
Without communication
Below 1 V
D37-9 (D) - D37-16 (GND)
B - V
Diagnostic tester communication
During communication
Pulse generation
D37-12 (EFII) - D37-16 (GND)
V - V
ECM input signal
Ignition switch OFF
11 to 14 V
D37-12 (EFII) - D37-16 (GND)
V - V
ECM input signal
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
Waveform 2
D37-13 (EFIO) - D37-16 (GND)
L - V
ECM output signal
Ignition switch OFF
Below 1 V
D37-13 (EFIO) - D37-16 (GND)
L - V
ECM output signal
Ignition switch ON
Waveform 3
D37-14 (VC5) - D37-5 (AGND)
P - G
Power source
No key is in ignition key cylinder
Below 1 V
D37-14 (VC5) - D37-5 (AGND)
P - G
Power source
Key is in ignition key cylinder
4.6 to 5.4 V
D37-15 (CODE) - D37-5 (AGND)
R - G
Transponder key amplifier communication signal
No key is in ignition key cylinder
Below 1 V
D37-15 (CODE) - D37-5 (AGND)
R - G
Transponder key amplifier communication signal
Key is in ignition key cylinder
Waveform 4
Inspect using an oscilloscope.
Waveform 1 (Reference)

Item
Content
Tester Connection
D37-4 (TXCT) - D37-5 (AGND)
Tool Setting
2 V/DIV., 10 ms./DIV.
Condition
Key is in ignition key cylinder
Waveform 2 (Reference)

Item
Content
Tester Connection
D37-12 (EFII) - D37-16 (GND)
Tool Setting
5 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
Waveform 3 (Reference)

Item
Content
Tester Connection
D37-13 (EFIO) - D37-16 (GND)
Tool Setting
2 V/DIV., 1 s./DIV.
Condition
Ignition switch ON
Waveform 4 (Reference)

Item
Content
Tester Connection
D37-15 (CODE) - D37-5 (AGND)
Tool Setting
2 V/DIV., 20 ms./DIV.
Condition
Key is in ignition key cylinder
| CHECK ECM |
Disconnect the B48 ECM connector and measure the resistance according to the value(s) in the table below.


If the result is not as specified, there may be a malfunction on the wire harness side.Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
B48-12 (E1) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the B48 ECM connector. Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the ECM may have a malfunction.Tester Connection
Wiring Color
Terminal Description
Condition
Specified Condition
D55-20 (IMO) - B48-12 (E1)
V - W-B
Transponder key ECU output signal
Ignition switch off
11 to 14 V
D55-20 (IMO) - B48-12 (E1)
V - W-B
Transponder key ECU output signal
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
Waveform 1
D55-14 (IMI) - B48-12 (E1)
L - W-B
Transponder key ECU input signal
Ignition switch off
Below 1 V
D55-14 (IMI) - B48-12 (E1)
L - W-B
Transponder key ECU input signal
Ignition switch ON
Waveform 2
Inspect using an oscilloscope.
Waveform 1 (Reference)

Item
Content
Tester Connection
D55-20 (IMO) - B48-12 (E1)
Tool Setting
5 V/DIV., 500 ms./DIV.
Condition
Within 3 seconds after starter operates and initial combustion occurs, or within 3 seconds after ignition switch first turned to ON after battery disconnected and connected.
Waveform 2 (Reference)

Item
Content
Tester Connection
D55-14 (IMI) - B48-12 (E1)
Tool Setting
10 V/DIV., 100 ms./DIV.
Condition
Ignition switch ON